Filter
Top Products
DXZ835MP 13
English
12 DXZ835MP
English
Basic Operations
7. OPERATIONS
Basic Operations
Note:Be sure to read this chapter referring to the front diagrams of
chapter “3. CONTROLS” on page 5 (unfold).
CAUTION
Be sure to lower the volume before switch-
ing off the unit power or the ignition key. The
unit remembers its last volume setting. If
you switch the power off with the volume up,
when you switch the power back on, the
sudden loud volume may hurt your hearing
and damage the unit.
Turning on/off the power
Note:
• Be careful about using this unit for a long time
without running the engine. If you drain the car’s
battery too far, you may not be able to start the
engine and this can reduce the service life of the
battery.
1. Press the [FNC] button.
2. The illumination and display on the unit light
up. The unit automatically remembers its last
operation mode and will automatically switch
to display that mode.
3. Press and hold the [FNC] button for 1 sec-
ond or longer to turn off the power for the
unit.
Note:
• System check
The first time this unit is turned on after the wire
connections are completed, it must be checked
what equipment is connected. When the power is
turned on, “SYSTEM CHCK” and “PUSH
POWER” appear in the display alternately, so
press the [FNC] button. The system check starts
within the unit. When the system check is
complete, press the [FNC] button again.
Selecting a mode
1. Press the [FNC] button to change the opera-
tion mode.
2. Each time you press the [FNC] button, the
operation mode changes in the following or-
der:
Radio mode ➜ CD/MP3/WMA mode ➜ DVD
deck mode ➜ CD changer mode ➜ MD
changer mode ➜ DVD changer mode ➜ TV
mode ➜ Radio mode...
∗ External equipment not connected with
CeNET is not displayed.
Adjusting the volume
Turning the [ROTARY] knob clockwise in-
creases the volume; turning it counterclockwise
decreases the volume.
∗ The volume level is from 0 (minimum) to 33 (maxi-
mum).
Switching the display
Press the [D] button to select the desired display.
Each time you press the [D] button, the display
switches in the following order:
Main display ➜ Clock display ➜ Main display
∗ Once selected, the preferred display becomes
the display default. When a function adjust-
ment such as volume is made, the screen will
momentarily switch to that function’s display,
then revert back to the preferred display sev-
eral seconds after the adjustment.
∗ When you have entered a title in a CD, it
appears in the main display. If you have not
entered a title, “NO TITLE” appears in the title
display instead. For information on how to
enter a title, refer to the subsection “Entering
titles” in section “Operations Common to
Each Mode”.
Setting the Beat EQ
This unit are provided with 3 types of sound
tone effects stored in memory. Select the one
you prefer.
∗ The factory default setting is “USER CUSTOM”.
Each time you press the [BEQ] button, the tone
effect changes in the following order:
“BASS BOOST” ➜ “IMPACT” ➜ “EXCITE” ➜
“USER CUSTOM” ➜ “TONE BYPASS” ➜
“BASS BOOST” ...
• BASS BOOST : bass emphasized
• IMPACT : bass and treble empha-
sized
• EXCITE : bass and treble empha-
sized mid de-emphasized
• USER CUSTOM : user custom
• TONE BYPASS : no sound effect
Adjusting the tone
Press the [A-M] button and select the item to
adjust. Each time you press the [A-M] button,
the item changes in the following order:
● When the BEQ (BASS BOOST, IMPACT,
EXCITE) is set
“BASS BOOST” ( IMPACT, EXCITE) ➜
“BALANCE” ➜ “FADER” ➜ Function
mode...
● When the BEQ (USER CUSTOM) is set
“BASS” ➜ “MID” ➜ “TREBLE” ➜
“BALANCE” ➜ “FADER” ➜ Function
mode…
● When the TONE BYPASS is set
“BALANCE” ➜ “FADER” ➜ Function
mode…
∗ Pressing the [BEQ] button for 1 second or
longer while in “USER CUSTOM” sets flat, and
displays a “BEQ FLAT” message.
Note:
•
When the separately-sold digital sound processor
(DVH920) is used, the bass and treble tone
adjustments cannot be selected.
Adjusting the bass
The bass gain, bass F (center frequency) and
bass Q can be adjusted as follows.
1. Press the [A-M] button and select “BASS
GAIN ”.
2. Press the [a] or [d] button and select
from “BASS GAIN ” ➜ “BASS F 50 ” ➜
“BASS Q 1 ” ➜ “BASS GAIN ”.
3. Turn the [ROTARY] knob clockwise or
counterclockwise as needed and adjust the
gain, the F (center frequency) and the Q.
BASS GAIN : –6 to 8 (The factory default
setting is “0”)
BASS F : 50Hz/80Hz/120Hz (The
factory default setting is “50”)
BASS Q : 1/1.25/1.5/2 (The factory
default setting is “1”)
4. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
Adjusting the MID
The MID gain, MID F (center frequency) and
MID Q can be adjusted as follows.
1. Press the [A-M] button and select MID GAIN.
2. Press the [a] or [d] button and select
from “MID GAIN ” ➜ “MID F 1k ” ➜
“MID Q 2 ” ➜ “MID GAIN ”.
3. Turn the [ROTARY] knob clockwise or
counterclockwise as needed and adjust the
gain, the F (center frequency) and the Q.
MID GAIN : –6 to 6 (The factory default
setting is “0”)
MID F : 700Hz/1KHz/2KHz (The factory
default setting is “1k”)
MID Q : 1.5/2 (The factory default
setting is “2”)
4. When the adfustment is complete, press the
[A-M] button several times until the function
mode is reached.
Adjusting the TREBLE
The treble gain and treble F (center frequency)
can be adjusted as follows.
1. Press the [A-M] button and select “TREB
GAIN”.
2. Press the [a] or [d] button and select
from “TREB GAIN ” ➜ “TREB F 12K ”
➜ “TREB GAIN ”.
3. Turn the [ROTARY] knob clockwise or
counterclockwise as needed and adjust the
gain and the F (center frequency).
TREB GAIN : –6 to 6 (The factory default
setting is “0”)
TREB F : 8KHz/12KHz (The Factory
default setting is “12K”)
4. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
Adjusting the balance
1. Press the [A-M] button and select “BALANCE”.
2. Turning the [ROTARY] knob clockwise
emphasizes the sound from the right speaker;
turning it counterclockwise emphasizes the
sound from the left speaker.
∗ The factory default setting is “0”. (Adjustment
range: L13 to R13)
3. When the adjustment is complete, press the
[A-M] button several times until the function
mode is reached.
Adjusting the fader
1. Press the [A-M] button and select “FADER”.
2. Turning the [ROTARY] knob clockwise
emphasizes the sound from the front
speakers; turning it counterclockwise
emphasizes the sound from the rear speakers.
∗ The factory default setting is “0”. (Adjustment
range: F12 to R12)