Filter
Top Products
EN
2006 Victor Company of Japan, Limited
1005MNMWTNTCN
CS-WDS1
CAR STEREO SPEAKER
LVT1405-002A
[E]
Thank you for purchasing the JVC Car Stereo Speakers. For the secure installation and perfect operation of your
speaker, please read the following instructions carefully.
The diaphragm of this speaker makes use of birch wood to faithfully reproduce the original sound.
Each unit, therefore, has a unique appearance.
Professional knowledge is required for mounting this speaker. For details, please consult the authorized dealer.
Make use of the paper pattern provided when processing the mounting board of the speaker.
During mounting, ensure that there is enough spacing to avoid hitting against any parts such as window glass.
In order to optimize the sound field of the wood cone, it is recommended that the speaker terminal be mounted at the
bottom with the wood grain in the vertical direction.
Notes for dealers
Upon completing the mounting, please hand this instruction manual to the customer.
Mounting the speaker
Type : 2-Way Separate Speaker
Frequency Response : 45 Hz - 50 kHz
Sound Pressure Level : 84 dB/W
0m
Recommended Crossover Frequency
: 4.5 kHz (Cut-off Slope:-12 dB/oct.)
14.5cm Wood Cone Woofer
Power Handling Capacity (Nominal)
: 50 W
Power Handling Capacity (Max. Music Power)
: 150 W
Impedance : 4
K
Frequency Response : 45 Hz - 8 kHz
Sound Pressure Level : 84 dB/W
0m
Mass : 1.5 k
g (one piece)
2cm Wood Dome Tweeter
Power Handling Capacity (Nominal)
: 50 W (4.5 KHz -12 db/oct. H.P.F.)
Power Handling Capacity (Max. Music Power)
: 150 W (4.5 KHz -12 db/oct. H.P.F.)
Impedance : 4
K
Frequency Response : 3 kHz - 50 kHz
Sound Pressure Level : 84 dB/W
0m
Mass : 235
g (one piece)
Designs and specifications are subject to change without notice.
Specifications
Be sure to install the speakers according to the directions so as to prevent them from slipping accidentally out of position due to the
repeated impact of opening and closing doors or the tossing and bumping of the vehicle.
Set the wiring firmly on the floor of the vehicle, taking the utmost care not to break wires while installing. When installing the speakers
in the doors, extra attention must be paid to allowing reasonable play to the wires. The wiring, if given too much clip or clamp, will get
pinched in between the door and body of the vehicle when opening and closing doors.
Since the speaker installed in the door is positioned at the foot level, be careful not to damage the speaker by giving it an inadvertent
kick. Check the water outlet at the bottom of the door occasionally to ensure that it drains well, leaving no rainwater inside the door.
Before connecting the speakers to the amplifier, confirm that the power has been turned off. The click noise generated by the
connection if the power is on may damage the speakers.
The amplifier and speakers should be connected between corresponding terminals, i.e. “left” to “left”, and “right” to “right”, as well as
“+” to “+”, and “–” to “–”. Connection with reversed polarity will degrade the quality of stereo reproduction.
Do not subject the speakers to excessive input. Any excessive input may damage the speakers.
Make sure that the output impedance of the amplifier’s speaker terminal is rated at 4 ohms.
Please use a high-pass filter.
(Cut-off Frequency is 4.5 kHz and above -12dB/oct)
When cleaning the speakers, use a soft cloth and wipe the surface gently. Do not apply thinner or solvent.
1.
2.
3.
4.
5.
6.
7.
8.
9.
For Proper Installation and Use
0606SKMSANTCN
INSTRUCTIONS
Accessories
Hexagonal head tapping screw
x 16 (R4 x 30 mm)
A Hexagonal head tapping screw
x 8 (R4 x 20 mm)
B Protection bar x 4C
Paper pattern
D
How to use the paper pattern
Cut out the paper pattern along the perforation.
Place and trace the paper pattern over the mounting
area on the vehicle or board.
Cut out the mounting area on the vehicle or board along
the marking.
1.
2.
3.
For Tweeter
For Woofer
Use a M4 hex wrench.
Thiele/ Small Parameter
(14.5 cm Woofer)
Revc (DC VC Res ) 3.4 Ohms
Imp. (300Hz)
4 Ohms
Fo (Res Freq )
80.2 Hz
Zo (Zmax at Fo)
26.9 Ohm
Sd (Piston Area) 0.0095 sqM
BL (Flux*Length) 6.08 TM
Qms (Mech Q) 3.814
Qes (Elec Q) 0.667
Qts (Total Q)
0.568
Vas (Acous Vol)
4.13 Litr
Le (Inductance) 0.286 mH
Cms (Compliance) 321.9 uM/N
Mms (Total Mass)
12.23 Gram
Mmd (DiaphmMass) 11.70 Gram
CS-WDS1_A4.indd 1 7/4/2006 9:51:12 AM