Filter
Top Products
27
ENHANCED COMMUNICATIONS 6
No.
Freq.
(Hz)
No.
Freq.
(Hz)
No.
Freq.
(Hz)
No.
Freq.
(Hz)
00 67.0 11 97.4 22 141.3 33 206.5
01 69.3 12 100.0 23 146.2 34 210.7
02 71.9 13 103.5 24 151.4 35 218.1
03 74.4 14 107.2 25 156.7 36 225.7
04 77.0 15 110.9 26 162.2 37 229.1
05 79.7 16 114.8 27 167.9 38 233.6
06 82.5 17 118.8 28 173.8 39 241.8
07 85.4 18 123.0 29 179.9 40 250.3
08 88.5 19 127.3 30 186.2 41 254.1
09 91.5 20 131.8 31 192.8 -- --
10 94.8 21 136.5 32 203.5 -- --
You will hear calls only when the selected tone is
received. To answer the call, press and hold Mic
[PTT], then speak into the microphone.
Skip steps 7 and 8 if you have already programmed
the appropriate CTCSS frequency.
Note:
◆ When using split-frequency operation, select FM mode on
both VFOs to use CTCSS.
◆ You can select a CTCSS frequency independent of a tone
frequency.
◆ You cannot use the CTCSS function with the Tone function.
CTCSS FREQUENCY ID SCAN
This function scans through all CTCSS frequencies to
identify the incoming CTCSS frequency on a received
signal. You may fi nd this useful when you cannot
recall the CTCSS frequency that the other persons in
your group are using.
1 While the CTCSS function is ON, press and hold
[AGC/T (SEL)].
• The current CTCSS frequency appears.
2 Press [SCAN (SG.SEL)] to activate the CTCSS
frequency ID scan.
• While the transceiver is receiving a signal, “ ”
blinks and every CTCSS frequency is scanned.
When the CTCSS frequency is identifi ed, the
transceiver stops scanning and the identifi ed
frequency is displayed.
• Press [SCAN (SG.SEL)] or [CLR] to stop
scanning while the CTCSS frequency ID scan is
active.
• Press [SCAN (SG.SEL)] again to resume
scanning.
Note: Received signals are audible while scanning is in
progress.
FM CTCSS OPERATION
You may sometimes want to hear calls only from
specifi c persons. When using FM mode, the
Continuous Tone Coded Squelch System (CTCSS)
allows you to ignore (not hear) unwanted calls from
other persons who are using the same frequency.
A CTCSS tone is sub-audible and is selectable from
among the 42 tone frequencies. Select the same
CTCSS tone as the other stations in your group. You
will not hear calls from stations other than those using
the same CTCSS tone.
Note: CTCSS does not cause your conversation to be private.
It only relieves you from listening to unwanted conversations.
1 Press [A/B (A=B)] to select VFO A or VFO B.
• “
” or “ ” appears to show which VFO is
selected.
2 Select the 29 MHz band or the 51-54 MHz band
using [28 (9)] or [50 (0)].
3 Select the desired frequency with the Tuning
control or MULTI/CH control.
4 Press [FM/AM (FM-N)] to select FM mode.
5 Turn the SQL control to adjust the squelch.
6 Press [AGC/T (SEL)] until “
” appears.
7 While “ ” is visible, press and hold [AGC/T
(SEL)].
• The current CTCSS frequency appears (default
is 88.5 Hz).
8 Turn the MULTI/CH control to select the
appropriate CTCSS frequency.
• The selectable CTCSS frequencies are listed in
the table below.
9 Press and hold [AGC/T (SEL)] or press [CLR] to
complete the setting.