Filter
Top Products
5655
56 57
CQ-VD7001U CQ-VD7001U
Tr ouble Shooting (continued)
English
English
❑ Error Display Messages
Note:
¡There may be cases when the disc numbers affected by an error are displayed before E1 and E2.
¡Displays and the steps to be taken for errors vary in part from changer to changer. For details, refer to the Operating
Instructions for the changer used.
■ CD/MP3/WMA/DVD/VCD (Video CD)/CD Changer/DVD Changer
An attempt was made to play a disc with a region number other than “1” or
“ALL”.
aPress [u] and check the disc.
REGION ERROR
No magazine is in the changer.
aLoad the changer with CD-loaded magazine.
NO MAGAZINE
No disc is in the player.
aInsert disc into the disc slot.
NO DISC
A WMA file can be copyrighted.
aThe file protected by copyright is not playable.
PROTECTED
The type of the file that is selected is not supported.
aCheck disc.
- E 4 -
No operation by some cause.
aPress [u]. If failure persists, press the reset switch. (Press the reset
switch in the CD changer). If normal operation is not restored, call the
store where you purchased the unit or the nearest Panasonic Servicenter.
- E 3 -
Disc has scratches.
aCheck disc.
- E 2 -
Disc is dirty, or is upside down.
aCheck disc.
- E 1 -
Display
Possible cause
a
Possible solution
■ XM Satellite Radio
Channel not in service.
a
This channel is not currently in service. Tune to another channel.
OFF AIR
XM broadcasts unreceivable because of poor receiving conditions.
a
Move to an area where XM broadcasts can be received well.
NO SIGNAL
XM antenna unconnected.
a
Connect the XM antenna.
ANTENNA
Cannot receive XM satellite radio.
a
Verify the wiring.
NO XM
❑ Product Servicing
If the suggestions in the charts do not solve the problem,
we recommend that you take it to your nearest authorized
Panasonic Servicenter. The product should be serviced
only by a qualified technician.
❑ Replacing the Fuse
Use fuses of the same specified rating (15 A). Using differ-
ent substitutes or fuses with higher rating, or connecting
the product directly without a fuse, could cause fire or
damage to this unit.
If the replacement fuse fails, contact your nearest
Panasonic Servicenter for service.
❑ If the Unit Begins to
Malfunction...
Reset switch
Insert a hard, slender stick into the hole and push the
switch.
Important
Push the switch only when the unit fails to operate with any
buttons. (Stored settings and adjustments are not cleared.)
If the unit fails to return to normal condition, call the near-
est Panasonic Servicenter and ask for repairs.
Note:
¡If the ID-CODE has been already set, you will be asked to
enter the ID-CODE right after the unit is restarted.
ENTER
TILT O/C
OPEN / CLOSE
EJECTON
DISC
TEXT
TUNE /
TRACK
Reset switch
Maintenance
❑ Cleaning this Unit
When the unit is dirty, wipe the surface of the display using
the Wiping Cloth (supplied).
Cleaning without the supplied cloth
1 Moisten the soft cloth in dishwashing
soap diluted with water and wring well.
2 Wipe lightly. Go over the same surface
with a dry cloth.
Note:
¡Since there is the possibility of water drops getting
inside of the unit, do not directly apply cleanser to the
surface.
¡Do not scratch the screen with your nails or other hard
objects. The resulting scratches or marks will obscure
the images.
❑ Caution on Cleaning
Your product is designed and manufactured to ensure a
minimum of maintenance. Use a dry soft cloth for routine
exterior cleaning. Never use benzine, thinner or other sol-
vents.
Alcohol
Pesticide
Wax
Benzine
Thinner
Caution
¡If water drops or similar wet substances get inside the
monitor, it may cause a malfunction.
Alcohol
Pesticide
Wax
Benzine
Thinner