Filter
Top Products
VQT5K75
18
“USB A NO DEVICE”
“USB B NO DEVICE”
• The USB device is not connected. Examine the
connection.
“DEVICE FULL”
• You cannot do recording because the remaining
recording time of the USB device is less than the total
time of the music source.
Change to a USB device which has enough recording
time and do the recording again.
“ERROR”
• An incorrect operation was done. Read the instructions
and try again.
“ERROR” (during recording)
• You cannot select other playback source (example:
radio, USB etc.) or press [:] or [9] during
recording. Stop the recording function.
• You cannot open the disc tray when recording from an
AM source.
“F61”
• Examine and correct the speaker cords connection.
• Disconnect the USB device. Switch off the system and
then switch it on again.
“F70”
• Examine the Bluetooth
®
device.
• Disconnect the Bluetooth
®
device. Switch off the
system and then switch it on again.
“F77”
• Switch off the system and then switch it on again.
“NO PLAY”
“UNSUPPORT”
• Examine the content. You can only play supported
format.
• The files in the USB device can be corrupted. Format
the USB device and try again.
• The unit may have a problem. Turn the unit off and
then on again.
“NO TRACK”
• There is no album or track in the USB device or the
internal memory.
“PLAYERROR”
• You played an unsupported MP3 file. The system will
skip that track and play the next one.
“REMOTE 1”
“REMOTE 2”
• The remote control and the main unit are using
different codes. Change the code of the remote
control.
- When “REMOTE 1” is shown, press and hold [OK]
and [1] for a minimum of 4 seconds.
- When “REMOTE 2” is shown, press and hold [OK]
and [2] for a minimum of 4 seconds.
“TEMP NG”
• The temperature protection circuit has been activated,
and the system will switch off. Let the unit cool down
before switching it on again.
• Check that the ventilation opening of the unit is not
obstructed.
• Ensure this unit is well ventilated.
“USB OVER CURRENT ERROR”
• The USB device is using too much power.
Disconnect the USB device, switch off the system and
then switch on again.
“VBR”
• The system cannot show the remaining play time for
variable bit rate (VBR) tracks.
System memory reset (initialization)
Reset the memory when the following situations occur:
• There is no response when buttons are pressed.
• You want to clear and reset the memory contents.
1 Disconnect the AC power supply cord.
2 While you press and hold [Í/I] on the main unit,
connect the AC power supply cord again.
Continue to press and hold the button (approximately
10 seconds) until “- - - - - - - -” is shown.
3 Release [Í/I].
All the settings are set back to the factory preset.
It is necessary to set the memory items again.
Remote control code
When other Panasonic equipment responds to the
remote control of this system, change the remote control
code for this system.
Preparation
Press [RADIO/EXT-IN] to select “AUX 1” or “AUX 2”.
1 Press and hold [RADIO/EXT-IN] on the main unit
and [2] on the remote control until “REMOTE 2”
is shown.
2 Press and hold [OK] and [2] for a minimum of
4 seconds.
1 Press and hold [RADIO/EXT-IN] on the main unit
and [1] on the remote control until “REMOTE 1”
is shown.
2 Press and hold [OK] and [1] for a minimum of
4 seconds.
Main unit displays
To set the code to “REMOTE 2”
To set the code to “REMOTE 1”
SC-MAX770PU_eng.book 18 ページ ２０１４年３月６日 木曜日 午後２時５４分