Filter
Top Products
Register your product and get support at
CEM210
EN Quick Start Guide
34
2
1
abc
efgh
d
L-CHR-CH
AMP
a
c
b
b
a
c
d
aa
b
c
d
a
b
e
f
c
d
g
h
i
b
c
d
Overview of parts
1
Check and identify the contents of your package:
1 In-car audio system
2 Sleeve
3 Front panel
4 Trim plate
5 Rubber cushion
6 Disassembly tools
7 Screws (4 pieces)
8 ISO connector
Connect wires
Caution
Ensure that all loose leads are insulated with
electrical tape.
For cars with ISO connectors
2 3
1
Pull out the ISO connectors from car
dashboard and connect them to the bigger
end of the supplied standard connector.
2
Connect the other end of the supplied stan-
dard connector to the unit.
3
&RQQHFWWKHDQWHQQDDQGDPSOLÀHUDVLO-
lustrated, if applicable. You can connect the
FDUDXGLRWRWKHDPSOLÀHUWKURXJK5&$72
5&$FDEOHVQRWVXSSOLHG
Connector Connect to
1 $17(11$ $QWHQQD
2 5($5/,1(2875 Rear right speaker
3 5($5/,1(287/ Rear left speaker
For cars without ISO connectors
3 4
Caution
Be sure to connect the black ground (earth)
OHDGÀUVW
1
&RQQHFWWKHDQWHQQDDQGDPSOLÀHUDV
illustrated, if applicable.
2
Cut off the bigger end of the supplied stan-
dard connector.
3
Check the car’s wiring carefully and connect
them to the supplied standard connector.
4
Connect the supplied standard connector to
the unit.
1 Green/black
strip
/HIWVSHDNHU
(Rear)
2 White/black
strip
/HIWVSHDNHU
(Front)
3 Gray/black
strip
Right speaker
(Front)
4 Purple/black
strip
Right speaker
(Rear)
e RED Ignition key +12V DC
ZKHQ21$&&
f %/8( Motor/electric antenna
relay control lead/
$PSOLÀHUUHOD\FRQWURO
lead
g %/$&. Ground
h Orange Illumination switch
i <(//2: To the +12V car battery
which is energized at all
times
Note
Check wire connection before you mount
the unit into a car.
If preset radio stations are lost when the
ignition key is turned OFF and then back
ON, reconnect the red leads crosswise to
the yellow ones.
Attach the front panel 5
1
$WWDFKWKHWULPSODWH
2
Insert the right side of the panel in the
chassis until it is correctly engaged.
3
Press the left side of the panel and point
the left hole at the left pillar.
4
Release the panel to engage the left side.
Mount in the dashboard 5
1
If the car does not have an on-board drive
or navigation computer, disconnect the
negative terminal of the car battery.
If you disconnect the car battery in a car
that has an on-board drive or navigation
computer, the computer may lose its
memory.
If the car battery is not disconnected,
to avoid short-circuit, ensure that bare
wires do not touch each other.
2
Remove the two screws on the top of the
unit.
3
Remove the mounting sleeve with the
supplied disassembly tools.
4
Ensure that car dashboard opening is
within these measurements:
5
Install the sleeve into the dashboard and
EHQGWKHWDEVRXWZDUGWRÀ[WKHVOHHYH
6
Place the rubber cushion over the end of
the bolt.
7
Slide the unit into the dashboard until you
hear a click sound.
8
Reconnect the negative terminal of the car
battery.
Turn on
1
Press
z
to turn on the unit.
To turn off the unit, press
z
for 3
seconds.
Set clock
1
Press MENU/DISP for 3 seconds.
2
Press
3
or
4
repeatedly to until the cur-
rently time is displayed.
3
Tu r n
z
clockwise to set hour.
4
Press
z
WRFRQÀUP
5
Tu r n
z
anti-clockwise to set minute.
6
Press
z
WRFRQÀUP
View clock
1
Press MENU/DISP repeatedly until the clock
is displayed.
5
5mm
5mm5mm
Listen to radio
1
Press SOURCE repeatedly to select Radio.
2
Press
3
or
4
to select band: [FM1],[FM2],
[FM3],[AM1], or [AM2] .
3
Press
∞
or
§
to tune to a radio station
manually.
To search for a radio station
automatically, press
/
for 3 seconds.
3OD\DXGLRÀOHV
1
Press on the front panel to release the
panel.
2
Insert a CD with the printed side facing up.
3
Close the panel.
Play starts automatically.
»
To pause CD play, press 1
.
To resume CD play, press
1
again.
Insert the USB device
1
Open the cover marked on the front
panel.
2
,QVHUWWKH86%GHYLFHLQWRWKH86%VRFNHW
7KHXQLWVWDUWVSOD\LQJIURPWKH86%
»
device automatically.
© 2009 Koninklijke Philips Electronics N.V.
All rights reserved.
CEM210_98_UM_V1.0