Filter
Top Products
Register your product and get support at
CEM220
EN Quick Start Guide
34
2
A1A2A3A4 A5A6A7A8
B1 B2 B3 B4 B5B6B7B8
A
A
B
abcd
B
b
a
c
d
aa
b
c
d
a
b
e
f
c
d
g
h
i
b
c
d
1
ab
efg
c
h
d
Overview of parts
1
These are the supplied parts needed to
connect and install this unit.
1 In-car audio system
2 Sleeve
3 Front panel
4 Standard connector
5 Trim plate (2 pieces)
6 Rubber cushion
7 Disassembly tools
8 Screws 4 pieces
Connect wires
Caution
Ensure that all loose leads are insulated with
•
electrical tape.
For cars with ISO connectors
2 3
1
Pull out the ISO connectors from car
dashboard and connect them to the bigger
end of the supplied standard connector.
2
Connect the other end of the supplied
standard connector to the unit.
3
Connect the antenna and amplifi er as
illustrated, if applicable.
Connector Connect to
1 REAR LINE OUT R Rear right
speaker
2 REAR LINE OUT L Rear left speaker
3 SUB OUT Subwoofer
4 ANTENNA Antenna
For cars with ISO connectors
3 4
Caution
Be sure to connect the black ground (earth)
•
lead fi rst.
1
Connect the antenna and amplifi er as
illustrated, if applicable.
2
Cut off the bigger end of the supplied stan-
dard connector.
3
Check the car’s wiring carefully and connect
them to the supplied standard connector.
4
Connect the supplied standard connector to
the unit.
1 Green/black
strip
Left speaker
(Rear)
2 White/black
strip
Left speaker
(Front)
3 Gray/black
strip
Right speaker
(Front)
4 Purple/black
strip
Right speaker
(Rear)
e RED Ignition key +12V DC
when ON/ACC
f BLUE Motor/electric antenna
relay control lead/
Amplifi er relay control
lead
g BLACK Ground
h Orange/
white
Illumination switch
i YELLOW To the +12V car battery
which is energized at all
times
Note
Check wire connection before you mount •
the unit into a car.
If preset radio stations are lost when the
•
ignition key is turned OFF and then back
ON, reconnect the red leads crosswise to
the yellow ones.
Attach the front panel 5
1
Attach the trim plate.
2
Insert the right side of the panel in the
chassis until it is correctly engaged.
3
Press the left side of the panel and point
the left hole at the left pillar.
4
Release the panel to engage the left side.
Mount in the dashboard 5
1
If the car does not have an on-board drive
or navigation computer, disconnect the
negative terminal of the car battery.
If you disconnect the car battery in a car that •
has an on-board drive or navigation computer,
the computer may lose its memory.
If the car battery is not disconnected, •
to avoid short-circuit, ensure that bare
wires do not touch each other.
2
Remove the two screws on the top of the
unit.
3
Remove the mounting sleeve with the
supplied disassembly tools.
4
Ensure that car dashboard opening is
within these measurements:
5
Install the sleeve into the dashboard and
bend the tabs outward to fi x the sleeve.
6
Place the rubber cushion over the end of
the bolt.
7
Slide the unit into the dashboard until you
hear a click sound.
8
Reconnect the negative terminal of the car
battery.
Turn on
1
Press
z
to turn on the unit.
• To turn off the unit, press
z
for 3
seconds.
Set clock
1
Press MENU/DISP for 3 seconds.
2
Press
3
or
4
repeatedly to until the cur-
rently time is displayed.
3
Turn
z
clockwise to set hour.
4
Press
z
to confi rm.
5
Turn
z
anti-clockwise to set minute.
6
Press
z
to confi rm.
View clock
1
Press MENU/DISP repeatedly until the clock
is displayed.
Listen to radio
1
Press SOURCE repeatedly to select Radio.
2
Press or to select band: [FM1], [FM2],
[FM3], [AM1], or [AM2] .
3
Press
∞
or
§
to tune to a radio station
manually.
5
5mm
5mm
To search for a radio station •
automatically, press SEARCH.
Play audio fi les
1
Press on the front panel to release the
panel.
2
Insert a CD with the printed side facing up.
3
Close the panel.
4
Press
2;
, to start play.
To pause CD play, press •
2;
.
To resume CD play, press •
2;
again.
Insert the USB device
1
Open the cover marked on the front
panel.
2
Insert the USB device into the USB socket.
»
ToThe unit starts playing from the USB
device automatically.
Insert SD/MMC card
1
Press to release the panel.
2
Insert the SD or MMC card into the card
slot.
»
The unit starts playing from the SD/
MMC card automatically.
© 2008 Koninklijke Philips Electronics N.V.
All rights reserved.
Quick Start Guide_CEM220.indd 1Quick Start Guide_CEM220.indd 1 2008-12-11 15:01:062008-12-11 15:01:06