Filter
Top Products
ìëêéè
çïðïî
ïïïíïì
ìëéè
çêïðïî
ïïïíïì
1. б©»® ÔÛÜ ø̱° ±º «²·¬ ó Ò±¬ ͸±©²÷ " This Blue LED illuminates when the unit is turned on.
2. ̸»®³¿´ ÔÛÜ ø̱° ±º «²·¬ ó Ò±¬ ͸±©²÷ " This Red LED illuminates if the amplifier internal
components become too hot and engage the thermal protection.The amplifier will shut down to cool
if this occurs.
3. Ю±¬»½¬ ÔÛÜ ø̱° ±º «²·¬ ó Ò±¬ ͸±©²÷ " This Yellow LED illuminates if a short circuit or too low
of an impedance is detected at the speaker connections.The amplifier will automatically shut down if
this occurs.
4. Ý¿-¬ ß´«³·²«³ Ø»¿¬-·²µ " The cast aluminum heatsink of the Power amplifier dissipates heat
generated by the amplifier's circuitry.
5. Í°»¿µ»® Ì»®³·²¿´- " The heavy duty,nickel-plated clamp wire connectors (
õ
and ó) will accept wire
sizes from 8 AWG to 18 AWG.
6. λ³±¬» Ы²½¸ ÛÏ øÑ°¬·±²¿´ ݱ²¬®±´´»®÷ " The Remote Punch EQ connection is made with a RJ-45
cable and can be installed in a variety of ways for easy control access.The control is used to boost low
and/or high frequency information to overcome road noise.The remote overrides the Punch EQ on the
amplifier when connected.
ÒÑÌÛæPrevious (prior to 2007) Punch Bass and Para-Punch remotes will not work with these amplifiers.
7. Ы²½¸ ÛÏ " This control is a narrow band adjustment variable from 0dB to +18dB @ 45Hz with a
Gyrator based Punch EQ that eliminates frequency shift with boost.
8. ײº®¿-±²·½ Ú·´¬»® " A 28Hz High Pass filter designed to prevent frequencies below the audio range
from being applied to the subwoofer from the amplifier.Consequently improving subwoofer
performance and power handling,particularly in vented enclosures.
9. Ê¿®·¿¾´» Ý®±--±ª»® " Is a built-in 24dB/octave Butterworth filter with a crossover point variable
from 35Hz to 250Hz.The crossover is set to Low-Pass (LP).
10. Ù¿·² ݱ²¬®±´ " The input gain control is preset to match the output of most source units.It can be
adjusted to match output levels from a variety of source units.
11. ÎÝß Ð¿--ó̸®« Ö¿½µ- " This Pass-Thru provides a convenient source for daisy-chaining an additional
amplifier without running an extra set of RCA cables from the front of the vehicle to the rear amplifier
location.
12. ÎÝß ×²°«¬ Ö¿½µ- " The industry standard RCA jacks provide an easy connection for signal level input.
They are nickel-plated to resist the signal degradation caused by corrosion.
13. ÎÛÓ Ì»®³·²¿´ " The heavy duty,nickel-plated captive c-clamp wire connector will accept wire sizes
from 12 AWG to 24 AWG.This terminal is used to remotely turn-on and turn-off the amplifier when
+12V DC is applied.
14. б©»® Ì»®³·²¿´- " The power and ground are nickel-plated captive c-clamp wire connectors and will
accommodate up to 4 AWG wire.
ì
Ü
ÛÍ×ÙÒ
Ú
ÛßÌËÎÛÍ