Filter
Top Products
Cautions
• This unit is designed for negative ground 12 V
DC operation only.
• Do not get the leads under a screw, or caught
in moving parts (e.g. seat railing).
• Before making connections, turn the car
ignition off to avoid short circuits.
• Connect the yellow and red power input
leads only after all other leads have been
connected.
• Run all ground leads to a common ground
point.
• Be sure to insulate any loose unconnected
leads with electrical tape for safety.
• The use of optical instruments with this
product will increase eye hazard.
Notes on the power supply lead (yellow)
• When connecting this unit in combination
with other stereo components, the connected
car circuit’s rating must be higher than the
sum of each component’s fuse.
• When no car circuits are rated high enough,
connect the unit directly to the battery.
Parts Iist (1)
• The numbers in the list are keyed to those in
the instructions.
• The bracket 1 and the protection collar 3 are
attached to the unit before shipping. Before
mounting the unit, use the release keys 6 to
remove the bracket 1 and the protection
collar 3 from the unit. For details, see
“Removing the protection collar and the
bracket (5)” on the reverse side of the sheet.
• Keep the release keys 6 for future use as
they are also necessary if you remove the
unit from your car.
Caution
Handle the bracket 1 carefully to avoid injuring
your fingers.
Note
Before installing, make sure that the catches on
both sides of the bracket 1 are bent inwards 2 mm
(
3
/32 in). If the catches are straight or bent outwards,
the unit will not be installed securely and may spring
out.
AUDIO OUT
FRONT
SUB OUT
AUDIO OUT
REAR
VIDEO IN
©2004 Sony Corporation Printed in Korea
CDX-M9900
3-265-746-11 (1)
Installation/Connections
Installation/Connexions
FM/AM
Compact Disc
Player
32
Equipment used in illustrations (not supplied)
Appareils utilisés dans les illustrations (non fournis)
Rear speaker
Haut-parleur arrière
Front speaker
Haut-parleur avant
Active subwoofer
Caisson de graves actif
54
CD/MD changer
Changeur de CD/MD
× 4
1
B
VIDEO IN
BUS AUDIO IN/AUX IN
BUS CONTROL IN
VIDEO IN
BUS AUDIO IN/AUX IN
BUS CONTROL IN
Source selector*
Sélecteur de source*
XA-C30
* not supplied
non fourni
A
× 2
Power amplifier
Amplificateur de puissance
6
Connection example (2)
Notes (2-A)
• Be sure to connect the ground lead before
connecting the amplifier.
• If you connect an optional power amplifier and do
not use the built-in amplifier, the beep sound will
be deactivated.
Tip (2-B- )
For connecting two or more CD/MD changers, the
source selector XA-C30 (optional) is necessary.
Connection diagram (3)
1To a metal surface of the car
First connect the black ground lead, then connect
the orange/white striped, yellow, and red power
input leads.
2To the power antenna control lead or power
supply lead of antenna booster amplifier
Notes
• It is not necessary to connect this lead if there is
no power antenna or antenna booster, or with
a manually-operated telescopic antenna.
• When your car has a built-in FM/AM antenna in
the rear/side glass, see “Notes on the control
and power supply leads.”
3To AMP REMOTE IN of an optional power
amplifier
This connection is only for amplifiers. Connecting
any other system may damage the unit.
4To the interface cable of a car telephone
5To a car’s illumination signal
Be sure to connect the black ground lead to a
metal surface of the car first.
6To the +12 V power terminal which is energized
in the accessory position of the ignition key
switch
Notes
• If there is no accessory position, connect to the
+12 V power (battery) terminal which is
energized at all times.
Be sure to connect the black ground lead to a
metal surface of the car first.
• When your car has a built-in FM/AM antenna in
the rear/side glass, see “Notes on the control
and power supply leads.”
7To the +12 V power terminal which is energized
at all times
Be sure to connect the black ground lead to a
metal surface of the car first.
8To the parking brake switch cord
Catch
1
DVD player DVX-11A
Lecteur DVD DVX-11A
7
2
1
Rotary commander RM-X4S
Satellite de commande RM-X4S