Filter
Top Products
22-EN
01GB04CDE101E.fm
ALPINE CDE-101E 68-09359Z76-B (EN)
USB Memory Connection (Optional)
Connect USB memory
1
Open the cover of the USB connection terminal.
2
Connect the USB memory directly to the USB
connection terminal, or via the USB cable.
Remove USB memory
1
Carefully, pull out the USB memory from the USB
cable or the USB connection terminal.
2
Close the cover of the USB connection terminal.
• Change to a source other than the USB memory mode, then remove
the USB memory. If the USB memory is removed in the USB memory
mode, data may be damaged.
• When removing USB memory, pull it out straight.
• If sound is not output or USB memory is not recognised even when
USB memory is connected, remove USB memory once, then connect
it again.
• Route the USB cable away from other cables, etc.
• After removing the USB memory, close the cover of the USB
connection terminal to prevent dust or foreign objects from entering
and causing a malfunction.
About MP3/WMA/AAC File of USB
Memory
Playing back MP3/WMA/AAC
MP3/WMA/AAC files are prepared, then stored to a USB
memory. This unit can recognise at least 100 folders (including
root folder) and 100 files per folder stored in USB memory.
Playback may not be performed if a USB memory exceeds the
limitations described above.
Do not make a file’s playback time more than 1 hour.
Media supported
This device can play back USB memory media.
Corresponding File Systems
This device supports FAT 12/16/32 for USB memory device.
* This illustrator is CDE-103EBT.
An iPhone/iPod can be connected to this unit by using the proprietary
ALPINE FULL SPEED
™
Connection Cable (KCE-433iV) (sold
separately). When this unit is connected by using the cable, the controls
on the iPod are not functional.
• Set AUX+ SETUP to OFF when an iPhone/iPod is connected (refer
to “Setting the AUX+ SETUP Mode” on page 17).
• If the Bluetooth INTERFACE (KCE-400BT) and an iPhone/iPod are
connected at the same time, be sure to disconnect the iPhone/iPod
from Bluetooth INTERFACE (KCE-400BT) while turning ACC to
OFF (CDE-102E/CDE-101E/CDE-101EM only).
• If you connect an iPhone to this unit, it can be used as an iPod. If you
use iPhone as a hands-free phone, use the unit (CDE-103EBT only)
in which the Bluetooth function is built, or use the Bluetooth
INTERFACE (KCE-400BT) (sold separately) (CDE-102E/
CDE-101E/CDE-101EM only).
• Internet and telephone functions of iPod touch or iPhone, etc., can
also be used when connecting to the unit. However, using these
functions will stop or pause the playing songs, at this time do not
operate the unit to avoid a malfunction.
• Do not leave an iPhone/iPod in a car, as its mechanism is sensitive to
high temperature and humidity conditions, and damage may result.
iPhone/iPod models usable with this unit
• The unit can be used with the following iPhone/iPod models.
iPhone 3G (version 2.0)
iPhone (version 1.1.4)
iPod touch (version 1.0.4)
iPod classic (version 1.1.1)
iPod nano (3 rd generation) (version 1.1)
iPod nano (2nd generation) (version 1.1.3)
iPod with video (version 1.2.3)
iPod nano (1st generation) ( version 1.3.1)
• For clarity in identifying your model of iPod, please see
Apple’s own document “Identifying iPod models” at
http://support.apple.com/kb/HT1353.
• This unit does not support video playback from iPhone/iPod,
even using a video-compatible cable.
• If the unit is used with versions of iTunes earlier than 7.6,
correct function and performance are not guaranteed.
USB memory
(Sold Separately)
Cable (Sold
Separately)
This unit
USB Connection Terminal
USB memory
(Sold Separately)
or
iPhone/iPod (Optional)
VIEW
/
/
ENT
Rotary encoder
/MUTE
/ESC
Preset buttons
(1 through 6)
4
5
6
2
SOURCE/
1
01GB04CDE101E.fm Page 22 Thursday, November 6, 2008 1:22 PM