Alpine CDE-103EBT Car Stereo System User Manual


 
33-EN
01GB05CDE101E.fm
ALPINE CDE-101E 68-09359Z76-B (EN)
Antenna Receptacle
Power Antenna Lead (Blue)
Connect this lead to the +B terminal of your power antenna,
if applicable.
This lead should be used only for controlling the vehicle’s power
antenna. Do not use this lead to turn on an amplifier or a signal
processor, etc.
Remote Turn-On Lead (Blue/White)
Connect this lead to the remote turn-on lead of your
amplifier or signal processor.
Audio Interrupt In Lead (Pink/Black)
Connect this lead to the Audio interface output of a cellular
phone which provides ground shorting when a call is
received.
Illumination Lead (Orange)
This lead may be connected to the vehicle’s instrument
cluster illumination lead. This will allow the backlighting of
this unit to dim whenever the vehicle’s lights are turned on.
Switched Power Lead (Ignition) (Red)
Connect this lead to an open terminal on the vehicle’s fuse
box or another unused power source which provides (+)12V
only when the ignition is turned on or in the accessory
position.
Battery Lead (Yellow)
Connect this lead to the positive (+) post of the vehicle’s
battery.
Ground Lead (Black)
Connect this lead to a good chassis ground on the vehicle.
Make sure the connection is made to bare metal and is
securely fastened using the sheet metal screw provided.
Power Supply Connector
Right Front (+) Speaker Output Lead (Grey)
Right Front (–) Speaker Output Lead (Grey/Black)
Right Rear (–) Speaker Output Lead (Violet/Black)
Right Rear (+) Speaker Output Lead (Violet)
Left Rear (+) Speaker Output Lead (Green)
Left Rear (–) Speaker Output Lead (Green/Black)
Left Front (–) Speaker Output Lead (White/Black)
Left Front (+) Speaker Output Lead (White)
Fuse Holder (10A)
Front Output RCA Connectors (CDE-103EBT/
CDE-102E only)
RED is right and WHITE is left.
Rear/Subwoofer Output RCA Connectors
(CDE-103EBT/CDE-102E only)
Front/Subwoofer Output RCA Connectors
(CDE-101E/CDE-101EM only)
RED is right and WHITE is left.
MIC Input Connector (CDE-103EBT only)
To Microphone.
RCA Extension Cable (sold separately)
Full Speed Connector
Control iPhone/iPod signals.
Connect this to an iPhone/iPod by using FULL SPEED™
Connection Cable (KCE-433iV) (sold separately) or to an
external device (such as a portable player) by using
conversion cable (KCE-237B) for building up the AUX IN
(sold separately).
Refer to “Setting the AUX+ SETUP Mode” (page 17).
You can also connect this to an optional Bluetooth
INTERFACE (KCE-400BT) (CDE-102E/CDE-101E/CDE-
101EM only). To use a hands-free mobile phone, an optional
Bluetooth INTERFACE (KCE-400BT) connection is required.
For details on connection, refer to the Owner’s Manual of the
Bluetooth INTERFACE (KCE-400BT).
FULL SPEED
TM
Connection Cable (KCE-433iV) (sold
separately)
KCE-400BT Connection Cable (Included with
KCE-400BT)
Front AUX Input Terminal (CDE-103EBT/CDE-102E
only)
This terminal allows for input of audio from an external
device (such as a portable player), using a commercially-
available converter cable.
USB Connection Terminal
Connect USB memory (sold separately)
AUX+ ON : When the external device is connected.
AUX+ OFF : When an iPhone/iPod is connected.
To prevent external noise from entering the audio system.
Locate the unit and route the leads at least 10 cm away from the car harness.
Keep the battery power leads as far away from other leads as possible.
Connect the ground lead securely to a bare metal spot (remove any paint, dirt or grease if necessary) of the car chassis.
If you add an optional noise suppressor, connect it as far away from the unit as possible. Your Alpine dealer carries various noise
suppressors, contact them for further information.
Your Alpine dealer knows best about noise prevention measures so consult your dealer for further information.
01GB00CDE101E.book Page 33 Monday, November 3, 2008 10:12 AM