Audiovox CE-200 Car Speaker User Manual


 
Fig. 1 Installation
I. Use universal template provided and locate on roof the desired mounting area. Observe cautions for possible interference in
headliner or steel roof.
2. Drill two 5/16" dia. holes through the fiberglass roof cap, the steel roof and headliner making certain the drill is 900 to the roof.
3. Enlarge the 5/16" holes in the fiberglass roof to 1 3/8" dia.
Warning -Only enlarge the two holes in the roof cap. Do not enlarge the holes in the steel roof or headliner.
4. Remove the inside headliner.
5. Assemble the two selected mounting bolts, cup washers, grommets, flat washers and jamb nuts to the steel roof using the wrench
provided. Make certain you apply sealant (not included) as shown.
6. Replace headliner.
7. Assemble radio mounting plate assembly to bolt studs as shown.
8. Complete wiring.
9. Place housing below radio plate assembly and connect speaker wiring to radio wiring.
10.Secure housing using six screws and washers provided.
11.Insert the two 1 3/8" plugs in fiberglass headliner using sealant to insure water-proof seal. .
12.See Fig. 4 if installing CElOO/CE200/CE300.
Fig. 2 Installation
I. Use universal template provided and locate on roof the desired mounting area. Observe cautions for possible interference in
headliner or steel roof.
2. Drill rn'o 5/16" dia. holes through the fiberglass roof cap, the steel roof and headliner making certain the drill is 900 to the roof.
J. Remove the inside headliner.
4. Assemble the two selected mounting bolts, cup washers, grommets, flat washers and jamb nuts to the steel roof using the wrench
provided. Make certain you apply sealant (not included} as shown.
5. Replace headliner.
6. Assemble radio mounting plate assembly to bolt studs as shown.
7. Complete wiring.
8. Place housing below radio plate assembly and connect speaker wiring to radio wiring.
9. Secure housing using six screws and washers provided.
IO.See Fig. 4 if installing CEI00/CE200/CEJOO.
Fig. 3 Installation
I. Use universal template provided and locate on roof the desired mounting area. Observe cautions for possible interference in
headliner or steel roof.
2. Drill two 5/16" dia. holes through the fiberglass roof cap, the steel roof and headliner making certain the drill is 90° to the roof.
3. Assemble the two selected mounting bolts, cup wash~rs, grommets, flat wa$hers and jamb nuts to the steel roof using the wrench
provided. Make certain you apply sealant (not included) as shown.
4. Assemble radio mounting plate assembly to bolt studs as shown.
5. Complete wiring.
6. Place housing below radio plate assembly and connect speaker wiring to radio wiring.
7. Secure housing using six screws and washers provided.
8. See Fig. 4 if installing CElOO/CE200/CE300.
Fig. 4 Installation
1. For figure I installation: Follow steps 1-11 then refer to Fig. 4 and follow instructions below it.
2. For figure 2 installation: Follow steps 1-9 then refer to Fig. 4 and follow instructions below it.
3. For figure 3 installation: Follow steps 1-7 then refer to Fig. 4 and follow instructions below it.
Figure 4 Installation: Only for CElOO/CE200/CE300
I. The entire housing and mounting plate (less radio) should now be secured to the roof as shown in Fig. 4
2. Insert mounting sleeve into housing opening and bend all tabs outward to secure it.
3. Reach through opening to access radio wimg connector and plug into radio.
4. Reach through opening to access antenna lead and plug into radio.
5. Pre-test radio.
6. Slide radio into housing until locked in place.