Filter
Top Products
INSTALLATION INSTRUCTIONS
UNIVERSAL INSTALLATION PROCEDURE USING MOUNTING SLEEVE
This unit is designed to fit into a standard DIN dashboard opening of 182 x 52 mm, common in many cars. If your
car does not have an existing opening of this size, it will be necessary to cut or file an opening to these dimensions.
The rear side (without the lip) of the mounting sleeve may be used as a template to cut the required opening.
In some cases, a special installation or adaptor kit may be required to properly mount the unit. For assistance or
answers to installation problems, call Audiovox toll-free at 1-800-645-4994 (Continental U.S. only, 9:00 AM-7:00 PM
Eastern Time Monday-Friday, 9:00 AM-5:00 PM Saturday, Holidays excluded), or consult with your local car stereo
specialist shop.
1. Remove the detachable front panel if it is attached to the chassis by pushing the “Release” button. Slide the
mounting sleeve off of the chassis. If it is locked into position, use the removal tools (supplied) to disengage it.
2. Check the dashboard opening size by sliding the mounting sleeve into it. If the opening is not large enough,
carefully cut or file as necessary until the sleeve easily slides into the opening. Do not force the sleeve into the
opening or cause it to bend or bow.
3. Check that there will be sufficient space behind the dashboard for the radio chassis.
4. In most installations, it is more convenient to complete the wiring before mounting the radio in the dashboard.
Follow the wiring diagram carefully and make certain all connections of the wiring harness are secure and
insulated with wire nuts or electrical tape to insure proper operation of the unit. After completing the wiring
connections, plug the 16-pin connector into the mating socket on the rear of the chassis, attach the front panel,
and turn the unit on to confirm operation (ignition switch must be “on”). If unit does not operate, re-check all wiring
until problem is corrected. Once proper operation is achieved, turn off the ignition switch, un-plug the wiring
harness from the chassis, and proceed with final mounting of the chassis.
5. Locate the series of bend tabs along the top, bottom, and sides of the mounting sleeve. With the sleeve fully
inserted into the dashboard opening, bend as many of the tabs outward as necessary so that the sleeve is firmly
secured to the dashboard.
6. Thread and tighten the supplied screw stud to the mating hole on the rear of the chassis. Place the radio in front
of the dashboard opening so that the wiring (16-pin connector, antenna lead, RCA leads if used, etc.) can be
brought through the mounting sleeve and plugged into the respective sockets on the rear of the chassis.
7. Carefully slide the radio into the mounting sleeve making sure it is right-side-up until it is fully seated and the
spring clips lock it into place.
8. Attach one end of the perforated support strap (supplied) to the screw stud using the hex nut provided. Fasten
the other end of the perforated strap to a secure part of the dashboard either above or below the radio using
the screw and hex nut provided. Bend the strap to position it as necessary.
CAUTION: The rear of the radio must be supported with the strap to prevent damage to the dashboard from
the weight of the radio or improper operation due to vibration.
9. Re-attach the front panel to the chassis and test radio operation by referring to the Operating Instructions for
the unit.
REMOVING THE RADIO FROM MOUNTING SLEEVE INSTALLATIONS
1. Should it be necessary to remove the radio for servicing or other reasons, first remove the detachable front panel.
2. Remove the rear support strap by taking off the hex nut securing it to the screw stud on the rear of the chassis.
3. Use the removal tools (supplied) to disengage the side spring clips and pull the radio out of the mounting sleeve.
ISO INSTALLATION PROCEDURE
This unit has threaded holes in the chassis side panels which may be used with the original factory mounting brackets
of some Toyota, Nissan, Mitsubishi, Isuzu, Hyundai and Honda vehicles to mount the radio to the dashboard. Please
consult with your local car stereo specialist shop for assistance on this type of installation.
1. Remove the existing factory radio from its dashboard or center console mounting. Save all hardware and brackets
as they will be used to mount the new radio.
2. Carefully un-snap the plastic frame from the front of the new radio chassis. Remove and discard the frame.
3. Remove the factory mounting brackets and hardware from the existing radio and attach them to the new radio.
CAUTION: DO NOT EXCEED M5X8MMMAXIMUM SCREW SIZE.
LONGERSCREWSMAY TOUCHANDDAMAGECOMPONENTSINSIDE THECHASSIS.
4. Wire the new radio to the vehicle as per step 4 above.
5. Mount the new radio assembly to the dashboard or center console using the reverse procedure of step 1.
-1-