Cadence ZRS C9 Car Amplifier User Manual


 
ZRS C9 QUICK INSTALLATION GUIDE
REMOTE TURN-ON
FROM HEAD UNIT
GROUND CONNECTION CABLE
SHOULD USE SAME GAUGE
WIRE AS POWER CABLE. KEEP GROUND CABLE AS
SHORT AS POSSIBLE. ALL AMPLIFIERS IN A MULTI-AMP
INSTALLATION SHOULD GROUND TO THE SAME
LOCATION TO AVOID GROUND LOOPS.
POWER CABLE REQUIREMENT:
4 GAUGE MINIMUM FOR 4-OHM BRIDGED OR 2-OHM STEREO
HIGH POWER INSTALLS. YOU MUST INSTALL AN ADDITIONAL
80 AMP IN-LINE FUSE IN THE MAIN POWER CABLE
CONNECTION.
We have spared no expense in designing these amplifiers, creating the most rugged,
reliable, powerful and best performing amplifiers. In fact we are so sure of the quality we
backup every ZRS Seriesamplifier with our exclusive two-year warranty which exemplifies
our commitment to excellence in car audio musical reproduction. (See enclosed warranty
card for details.)
Please read this installation guide carefully for proper use of your Cadence power amplifier.
Should you need technical assistance during or after your installation please call our
technical-line between 9:30 am and 5:00 PM EST at 732/370-5400. Read this entire guide
fully before attempting your installation.
When installing the amplifier, secure it tightly. An unmounted amplifier in your car can cause
serious injury to passengers and damage to your vehicle if it is set in motion by an abrupt
driving maneuver or short stop.
We suggest you construct a Red wiring harness with 2 additional fuse. One fuse should be
located near the car battery. This fuse near the battery offers protection against damage
from short circuits to the car chassis between the battery and the amplifier. A second fuse
closer to the amplifier offers additional safety to the amplifier itself. This fused red power
wire should be attached to the amplifier power terminal marked 12V+.
The wire harness should be made of primary cable of at least 4 gauge. The harness should
terminate in a large ring terminal for connection directly to the positive terminal of the car
battery. Use a spade plug to attach the wire, which connects to the amplifier location
marked 12V+.
A second black color wire of equal gauge should be used as a ground connection to a
welded chassis member. When connecting the ground wire make sure that there is no paint
or other insulator blocking a good ground connection. When installing multiple amplifiers,
mount them in close proximity so that they can all share the same ground point. Attach the
black ground wire to the amplifier screw terminal marked Ground.
We recommend that you use the Cadence amplifier installation kits, which contain all the
cabling and accessories necessary for a good, reliable installation.
Over the years we have received amplifiers back to our service department with melted
power/ground terminals. The cause of this is a bad ground connection. When there is a lack
of good ground, heat builds up at the weakest point which happens to be the contact screw
of the amplifier terminal. Over time the heat generated will begin to melt the terminal. It is a
good practice to feel the power and ground wires with your hands, near their amplifier
connection after having played the amp for a while. If the wires feel hot to the touch you
probably have a bad or loose connection. If you are sure of your connections and the wires
still feel hot to the touch, you should upgrade the gauge of wire to next heaviest gauge.
The remote turn on connection is located on the barrier strip next to the power and ground
connections. This connection is responsible for turning the amplifier on and off with the rest
of the system. A smaller gauge wire can be used to make this connection to your radio's
power antenna lead. Should your system not have any turn on leads, you can wire the
remote terminal to an accessory lead, which turns on, with your cars ignition.
The ZRS Series amplifiers feature RCA preamp inputs. Run RCA cables from your sound
source to the inputs of the amplifier. We suggest the use of high quality shielded RCA patch
cords to help reduce and eliminate unwanted electrical noise to your system.
To avoid electrical noise from being injected in to your sound systems be sure to run the
RCA cables on the opposite side of the vehicle that you used to carry the power and ground
leads of the amplifier.
WARNING: BE AWARE! Use of this amplifier at extreme high volumes for extended
periods of time may cause hearing loss and or hearing damage. During periods of
prolonged high volume levels it is recommended that you use ear safety devices. Playing
Cadence amplifiers at high volume levels while driving will impair your ability to hear
necessary traffic sounds. While driving always keep your sound volume at reasonable
levels. We at Cadence want you listening for many years to come.
ZRS Type C9 - 4 Channel High Power Amplifier
4 x 100 Watts RMS
4 x 150 Watts RMS
2 x 300 Watts RMS
2 x 600 Watts = 1200 Watts Max
640 @ 100Hz
200mV to 9Volt
45Hz-4.5KHz utilizing Multiplier
12db Channels 1 and 2
12db or 24dB Channels 3 and 4 Selectable
Channels 3 and 4 Capable
10Hz-360Hz
Flat to +7dB
Flat to +12dB @ 45Hz
4 Channel Mixed Mono RCA
2 or 4 Channel Selectable
<0.1%
10Hz - 40Khz +/- 3dB
9.6” x 2.32” x 15.11” (243x59x384mm)
4-Ohm Power:
2-Ohm Power:
4-Ohm Bridged:
IHF-2002 Peak Power:
Damping Factor:
Preamp Input Voltage:
Low Pass Crossover:
LP Crossover Slope:
Band Pass Control:
Subsonic HP Frequency:
Bass Focus Control:
Bass Equalizer:
Preamp Output:
Input Channels:
Minimum THD:
Frequency Response:
Dimensions:
80 AMP FUSE