Filter
Top Products
12 5
REAR PANEL CONTROLS
1. Fan
This is a variable speed cooling fan. Cool air enters the amplifier
through the fan filters located on the front of the amplifier. Be sure
not to block these ports when installing the amplifier or other
equipment.
2. Input connectors
Connect the input source to the balanced combo connectors
using either XLR or 1/4” TRS plugs. They are configured as fol-
lows : Pin 2 (Tip) hot, Pin 3 (Ring) cold, and Pin 1 (Sleeve)
ground. We recommend using balanced three-conductor cabling
wherever possible. Unbalanced two-conductor 1/4” plugs can
also be inserted into these inputs, but you will get better signal
quality and less noise and hum if you use balanced lines. Stereo
signal should be connected to the Channel 1 and Channel 2 input
jacks. When operating the unit in Bridged Mono or Parallel
modes, use the Channel 1 input jack only.
3. Link connectors
These jacks are used to send a parallel signal to another device
or amplifier.
4. High Pass Filter (HPF) switch.
These switches are used to activate the built-in High Pass Filter.
The HPF rolls off signals below 40Hz. This improves bass per-
formance by limiting sub-audio cone motion, making more power
available for the speaker’s rated frequency range. When the filter
is turned off, a 5 Hz roll off protects against DC or deep sub-audio
inputs.
5. Limiter switch
When the input signal connected to your amplifier is too high, you
end up with a distorted output signal. To prevent this, both chan-
nels feature a clip limiter that can be engaged or disengaged
selectively.
6. Bridge / Stereo / Parallel switch
This switch changes the amplifier operating mode between
stereo, mono bridged, and parallel.
7. 5-way Binding Post
Connect each channel of the unit to your speakers. Binding posts
are provided for each channel as well as Speakon
®
connectors, so
that paralleling of speakers is possible. Connection to the binding
posts can be made with bare wire, banana plugs, or spade lug
terminations. Make connections to both the Channel 1 and
Channel 2 terminals for Stereo or Parallel Mode, or a single
connection across the red terminals only of Channel 1 and
Channel 2 for Bridged Mono Mode.
8. Speakon® output connectors
You can use these to connect each channel of the unit to 8 ohms
or 4 ohms loudspeakers. Using Speakon® speaker cables, make
connections to both the channel 1 and channel 2 connectors for
Stereo or Parallel Mode, or to the Bridged mode connector for
Bridged Mono Mode.
9. Circuit breaker
The breaker acts in place of common disposable fuses. This cir-
cuit breaker will trip if there is a fault with the main voltage or if
maximum output is exceeded. Simply depress the circuit breaker
and power up the unit again.
10. AC input
IEC connector for AC power cable. Connect the supplied heavy-
gauge 3-pin IEC power cable.
WARRANTY & RETURN POLICY
Who’s covered by this warranty?
Cerwin-Vega’s Limited Warranty on professional audio products extends only to the original purchaser as evidenced by the original Bill
of Sale and only for the products purchased from authorized Cerwin-Vega dealers. Ten words of advice: retain the original bill of sale in
a safe place!
What’s covered by this warranty?
Cerwin-Vega warrants that all new professional audio products shall be free from defects in material and workmanship, under normal
and proper use. During the warranty period, Cerwin-Vega agrees to repair or replace (at our option) all such defective parts at no charge
for labor or materials.
What’s Not covered by this warranty?
This Limited Warranty does not apply to defective equipment that: has been altered or repaired by other than factory approved proce-
dures; has been subjected to negligence, misuse or accident; has been damaged by improper line voltage; had its serial number or any
part of it altered, defaced, or removed; or has been used in a way that is contrary to Cerwin-Vega’s written instructions. Except as pro-
vided by statute, this Limited Warranty does not cover losses, consequential or otherwise, resulting from the improper use of, or inabili-
ty to operate, any Cerwin-Vega product.
How long Does the warranty Extend?
Cerwin-Vega’s Limited Warranty extends for a period of (5 ) years for all non-powered speaker systems and related components and (3)
years for all stand-alone power amplifiers and related components from date of purchase as shown on the original Bill of Sale. The war-
ranty period will be extended if the warranty repairs have not been performed due to delays caused by circumstances beyond the con-
trol of the original purchaser, or if the warranty repairs did not remedy the defect and the original purchaser notifies Cerwin-Vega or the
original dealer or an Authorized Cerwin-Vega Service Center of the failure of the repairs within 30 days after they were completed.
How Do you get warranty Service?
In order to obtain warranty service, contact your original dealer or distributor, or an Authorized Cerwin-Vega Service Center. If, for some
reason, you have trouble locating a service representative, contact Cerwin-Vega’s Customer Service Department for assistance:
Cerwin-Vega! Customer Service Dept.
P.O. Box 816667
Hollywood, FL 33081
In some cases, the Customer Service Department can solve a service problem without any return of equipment to Cerwin-Vega, there-
by avoiding transit delays.
Phone: 954.316.1500 option 5 Fax: 954.316.1590.
E-mail: info@cerwin-vega.com
Now, what if the product must be returned?
If the Customer Service Department determines that the equipment must be returned to Cerwin-Vega for service, a Return Authorization
will be issued, and the defective merchandise may be shipped directly to the above address freight prepaid, along with a copy of both
the Return Authorization and the original Bill of Sale. The product will be repaired or replaced (at our option) and returned to the original
purchaser. Only the return postage will be paid by Cerwin-Vega. Cerwin-Vega will not be responsible for damage occurring in shipment
from the original purchaser or due to improper packing materials. Remember to pack all equipment carefully and in the original carton if
possible. Additional charges may be added if new packing materials are required for return shipment. SAVE YOUR ORIGINAL
PACKING MATERIALS!
Other remedies under the law
The exercise of any of the provisions under the Limited Warranty does not affect the protections or remedies of the original purchaser
under other laws. If you have additional questions about service, write or call the Customer Service Department. This Limited Warranty
applies to all Cerwin-Vega Professional products, and supersedes all previous warranty statements. Cerwin-Vega reserves the right to
make changes in product design and specifications at any time.
EXCEPT AS PROVIDED HEREIN AND BY APPLICABLE LAW, CERWIN-VEGA MAKES NO ADDITIONAL REPRESENTATION or WAR-
RANTY OF ANY NATURE WHATSOEVER, EXPRESSED OR IMPLIED, AS TO THE EQUIPMENT, INCLUDING BUT NOT LIMITED TO,
THE MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, DESIGN CONDITION OR WORKMANSHIP OF THE EQUIP-
MENT, OR THE QUALITY OF THE MATERIAL INCLUDED THEREIN, THIS LIMITED WARRANTY CONSTITUTES THE SOLE AND
ENTIRE AGREEMENT BETWEEN CERWIN-VEGA AND THE ORIGINAL PURCHASER
MANUAL_CVAMPS-REV-B1.qxd:Originator: M. Schlazer Size: 8.5 x 11 7/30/08 11:34 AM Page 5