Filter
Top Products
DXZ435 19
English
18 DXZ435
English
Operations Common to Each ModeOperations Common to Each Mode
5. Press the [DISP] button to select a character.
Each time you press the [DISP] button, the
character changes in the following orders:
Numbers ➜ Symbols ➜ Capital letters ➜
Numbers…
6. Turn the [ROTARY] knob to select the
desired character.
7. Repeat step 4 to 6 to enter up to 30
characters for message.
8. Press and hold the [ ] button for 2
seconds or longer to store the message in
memory and cancel input message.
9. Press the [TITLE] button to return to the
previous mode.
Setting the method for title scroll
Set how to scroll in CD-TEXT or MD.
∗ The factory default setting is “ON”.
1. Press and hold the [TITLE] button for 1
second or longer to switch to the adjustment
selection display.
2. Press the [a] or [d] button to select
“SCROLL”.
3. Turn the [ROTARY] knob clockwise or
counterclockwise and select “ON” or “OFF”.
● ON:
To scroll automatically.
● OFF:
To scroll just 1 time when the title was
changed or the title key was pressed.
4. Press the [TITLE] button to return to the
previous mode.
Dimmer control
You can set the dimmer control on or off.
∗ The factory default setting is “ON”.
1. Press and hold the [TITLE] button for 1
second or longer to switch to the adjustment
selection display.
2. Press the [a] or [d] button to select
“DIMMER”.
3. Turn the [ROTARY] knob clockwise to “ON”
or counterclockwise to “OFF”.
4. Press the [TITLE] button to return to the
previous mode.
Adjusting the display contrast
You can adjust the display contrast to match the
angle of installation of the unit.
∗ The factory default setting is “5”. (Adjustment
level:1to 8)
1. Press and hold the [TITLE] button for 1
second or longer to switch to the adjustment
selection display.
2. Press the [a] or [d] button to select
“CONTRAST”.
3. Turn the [ROTARY] knob clockwise or
counterclockwise to adjust the contrast.
4. Press the [TITLE] button to return to the
previous mode.
Setting LOW PASS FILTER
This function allows you to set the low-pass filter
sub-woofer output.
∗ The factory default setting is “LPF 120”.
1. Press and hold the [TITLE] button for 1
second or longer to switch to the adjustment
selection display.
2. Press the [a] or [d] button to select “SW
LPF”.
3. Turn the [ROTARY] knob clockwise or
counterclockwise to select the setting. Each
time you turn the [ROTARY] knob, the setting
changes in the following order:
REAR ➜ LPF 50 ➜ LPF 80 ➜ LPF 120
4. Press the [TITLE] button to return to the
previous mode.
Selecting AUX IN sensitivity
Make the following settings to select the
sensitivity when sounds from external devices
connected to this unit are difficult to hear even
after adjusting the volume.
∗ The factory default setting is “MID”.
1. Press and hold the [TITLE] button for 1
second or longer to switch to the adjustment
selection display.
2. Press the [a] or [d] button to select “AUX
SENS”.
3. Turn the [ROTARY] knob clockwise or
counterclockwise as needed and select from
“HIGH”, “MID” or “LOW”.
4. Press the [TITLE] button to return to the
previous mode.
Setting the clock
1. Press and hold the [TITLE] button for 1
second or longer to switch to the adjustment
selection display.
2. Press the [a] or [d] button to select
“CLOCK”.
3. Press the [ ] button.
4. Press the [a] or [d] button to select the
hour or the minute.
5. Turn the [ROTARY] knob clockwise or
counterclockwise to set the correct time.
∗ The clock is displayed in 12-hour format.
6. Press the [ ] button to store the time into
memory.
7. Press the [TITLE] button to return to the
previous mode.
Note:
•You cannot set the clock when it is displayed with
only the ignition on. If you drain or remove the
car’s battery or take out this unit, the clock is
reset. While setting the clock, if another button or
operation is selected, the clock set mode is
canceled.
Entering titles
Titles up to 8 characters long can be stored in
memory and displayed for CD, CD changer and
TV stations. The number of titles that can be
entered for each mode are as follows.
Mode Number of titles
CD mode 50 titles
TV mode 20 titles
CD changer mode Number of titles
DCZ625 connected 100 titles
CDC655Tz connected 100 titles
CDC1255z connected 50 titles
6. Press the [DISP] button to select a character.
Each time you press the [DISP] button, the
character changes in the following order:
Numbers ➜ Symbols ➜ Capital letters ➜
Numbers...
7. Turn the [ROTARY] knob to select the
desired character.
8. Repeat steps 5 to 7 to enter up to 8
characters for the title.
9. Press and hold the [ ] button for 2
seconds or longer to store the title into
memory and cancel title input mode.
Clearing titles
1. Select and play a CD in the CD changer or
tune in to a TV station for which you want to
clear the title.
2. Press the [DISP] button and display the sub.
3. Press the [TITLE] button.
The display switches to the title input display.
4. Press the [BND] button.
5. Press and hold the [ ] button for 2
seconds or longer to clear the title and
cancel title input mode.
AUX function
This system has an external input jack so you
can listen to sounds and music from external
devices connected to this unit.
1. Press the [FNC] button to select the mode
you want to enter a title (CD, CD changer or
TV).
2. Select and play a CD in the CD changer or
tune in to a TV station for which you want to
enter the title.
3. Press the [DISP] button and display the sub.
4. Press the [TITLE] button. The cursor position
flashes.
5. Press the [a] or [d] button to move the
cursor.