Filter
Top Products
CDMP-2600
FUNCTIONS: (CONTINUED)
12
BPM: Press and hold the BPM button to turn on the BPM read out, once
on you may TAP the button to the beat of the music, after a few TAPS
the display will read out the average BEATS PER MINUTE of the track.
PGM: Allows you to create a set playlist. To program a set list into the
CDMP-2600 memory, begin by stopping the unit from play and press-
ing PGM to begin the set list. Select a track by using the track selection
button to scan to the first track to be placed in the set list.
When you have selected the proper track press PGM and the
CDMP-2600 will be ready to set your next selection. Repeat the previ-
ous steps until you have completed your playlist, then press play to
begin the set list.
PITCH: Pushing the PITCH button activates the PITCH CONTROL SLIDE.
The PITCH button has three settings 8%, 12% and 24% and can be
toggled by pressing the PITCH button once for each setting . Push the
PITCH button again to deactivate this mode.
PITCH CONTROL SLIDE: Moving the PITCH CONTROL SLIDE
up or down will lower or raise the pitch percentage up to + or - 24%
depending on the PITCH BUTTON setting.
PITCH BEND: Pushing the PITCH BEND BUTTONS will automatically
bend the pitch up to +26% or bend the pitch down to -26% depending
on the setting of the PITCH BUTTON. Releasing the buttons will return
the pitch to the original pitch setting. You can use this function to match
the beat when mixing from one song to another.
LOOP SECTION: A LOOP repeats the section between the entry point
(IN) and the exit point (OUT). To set a loop while the unit is playing,
start by pressing the IN BUTTON (it will light up) and when you reach
the desired end loop point press the OUT BUTTON (it will also light up).
The loop will continue playing until you press the OUT BUTTON again
allowing the music to continue from that point on, to re-engage the loop
you must press the RELOOP BUTTON. When you have released your
loop the OUT BUTTON will turn OFF and the IN BUTTON will remain lit
to indicate that your loop is stored in the CDMP-2600 memory. Pressing
the IN BUTTON again while the unit is playing will erase the previously
saved loop while saving your new loop entry point. Press OUT to exit
the loop and save a new complete loop.Press RELOOP to return to the
beginning of the previously saved loop from normal play. Press
RELOOP repeatedly to cause the loop to stutter.
NOTE: THE FIRST LOOP WILL HAVE A PAUSE AT THE EXIT POINT, WHILE ALL
OTHERS WILL BE SEAMLESS.
PLAY/PAUSE: Each press of the PLAY/PAUSE BUTTON
causes the operation to change from PLAY to PAUSE or from PAUSE
back to PLAY. The PLAY/PAUSE BUTTON remains lit when in PLAY
mode, while it blinks in PAUSE mode.
CUE: While the unit is playing and after the cue point has been
programmed, pressing CUE will cause the CD player to enter the
PAUSE mode (PLAY/PAUSE BUTTON blinks) at the programmed cue
point (the CUE LED is lit). Holding down the CUE button
changes the function to preview , and allows you to stutter start or play
from the programmed CUE POINT Releasing the CUE button will return
the CD to the preset CUE point.
REPEAT: Press the repeat button once to engage 1 or repeat the
selected track. Press REPEAT again to engage ALL setting which will
repeat all the tracks on the CD. Press REPEAT again to disengage the
repeat function.
13
14
15
16
17
18
19
20
5
SPECIFICATIONS:
GENERAL:
Type.........................................Compact Disc Player & USB Mp3 Reader
Disc Type...................................Standard Compact discs (12 cm & 8 cm)
Time Display....................Track Elapsed, Track Remain, or Total remain
Variable Pitch.......................................± 24% Slider with Resume Switch
Pitch Bend............................................................................± 26% Maximum
Instant Start....................................................................Within 0.03 seconds
Installation...........................................................................................19" each
Dimensions...........Main unit: 19" x 3.5" x 10" (482.6 x 88.9 x 254mm)
…….........…Remote unit: 19" x 3.5" x 3.5" (482.6 x 88.9 x 88.9 mm)
Weight Per Unit..................................................Main unit: 5.5 lbs. (2.5 kg)
…...................................................................Remote unit: 3.85 lbs.(1.74kg)
AUDIO SECTION:
Quantization......................................1 Bit Linear/Channel, 3 Beam Laser
Oversampling Rate..............................................................................8 Times
Sampling Frequency.........................................................................44.1 kHz
Frequency Response............................................................20 Hz to 20 kHz
Total Harmonic Distortion...................................................Less Than 0.05%
Signal to Noise Ratio..............................................................................85 dB
Dynamic Range.......................................................................................85 dB
Channel Separation.................................................................85 dB (1 KHz)
Output Level...................................................................2.0 +/- 0.2V R.M.S.
Power Supply......................................................AC 115/230V, 60/50 Hz
SPECIFICATIONS AND DESIGN ARE SUBJECT TO CHANGE
WITHOUT NOTICE FOR PURPOSE OF IMPROVEMENT.
21
USB PORT The USB port allows the connection of any USB mass stor-
age device*.
USB/CD SELECT BUTTON The USB/CD select button allows you to
toggle from the CDMP-2600 internal CD drive and the mass storage
device connected to the USB port.
TRACK SELECTION ROTARY: The TRACK SELECTION ROTARY
allows you to navigate through folders or search through tracks
depending on weather you are in USB mode or CD mode.
In CD mode the rotary can search through cd tracks, turning the
rotary to the right or clock-wise advances the selection, and turning
the rotary to the left or counterclock-wise decreases the selection.
In USB mode the ROTARY knob allows you to search through folders
and navigate through music libraries on your USB device.
TO CHOOSE A FOLDER: Press and hold the TRACK SELECTION
ROTARY and turn it clockwise or counterclockwise to the folder you
wish to search through, once you have found the disered folder,
release the TRACK SELECTION ROTARY and the display will show
the first song in that folder. Once in a folder you can turn the
TRACK SELECTION ROTARY to the song you wish to play and the
CDMP-2600 will either automatically load the song when in single
mode or play the song when in continuous mode.
NOTE : ONCE YOU HAVE SKIPPED TO ANOTHER TRACK, YOU MAY NOT GO BACK TO YOUR PRO-
GRAMMED CUE POINT. YOU MUST BEGIN YOUR CUE SELECTION OVER AGAIN, THE CUE
WILL BE PRESET TO THE BEGINNING OF THE NEWLY SELECTED TRACK.
We recommend that you use a MASS STORAGE DEVICE that is no
larger than 2 gb and that only has less than 100 folders with less
than 1000 songs in any one folder. larger drives will work but they
will greatly affect the time in which it takes to search and or load a
song.
22
23
*