Filter
Top Products
SPECIFICATIONS
40.2cs
Type: 4" 2-Way System
Speaker Impedance: 4 Ohms
Power Handling: 75W RMS, 300W peak
Frequency
Response (±3dB): 80Hz ~ 21kHz
Sensitivity: 89dB
Crossover Frequency: 3.5kHz
Mounting Depth,
Drop-in – Midrange: 1-13/16" (47mm)
Cutout Diameter
Midrange: 3-3/4" (96mm)
Cutout Diameter – Tweeter: 1-3/4" (45mm)
50.2cs
Type: 5-1/4" 2-Way System
Speaker Impedance: 4 Ohms
Power Handling: 85W RMS, 340W peak
Frequency
Response (±3dB): 59Hz ~ 21kHz
Sensitivity: 89dB
Crossover Frequency: 3.5kHz
Mounting Depth, Drop-in: 2-3/8" (61mm)
Cutout Diameter: 4-13/16" (123mm)
Cutout Diameter – Tweeter: 1-3/4" (45mm)
60.2cs
Type: 6-1/2" 2-Way System
Speaker Impedance: 4 Ohms
Power Handling: 90W RMS, 360W peak
Frequency
Response (±3dB): 50Hz ~ 21kHz
Sensitivity: 89dB
Crossover Frequency: 3.5kHz
Mounting Depth, Drop-in: 2-7/16" (62mm)
Cutout Diameter: 5-1/8" (131mm)
Cutout Diameter – Tweeter:1-3/4" (45mm)
652.2cs
Type: 165mm 2-Way System
Speaker Impedance: 4 Ohms
Power Handling: 90W RMS, 360W peak
Frequency
Response (±3dB): 50Hz ~ 21kHz
Sensitivity: 89dB
Crossover Frequency: 3.5kHz
Mounting Depth, Drop-in: 2-1/2" (64mm)
Cutout Diameter: 5-11/16" (145mm)
Cutout Diameter – Tweeter:1-3/4"(45mm)
DECLARATION OF CONFORMITY
We, Harman Consumer International
2, route de Tours
72500 Chateau-du-Loir
France
Lutz Uphoff
Harman Consumer International 12/99
declare in own responsibility, that the products described in this owner’s manual are in compliance with technical standards:
EN 50081-1:1992
EN 50082-1:1992
Infinity Systems, Inc. • 250 Crossways Park Drive
Woodbury, NY 11797 USA • (800) 553-3332 • FAX (516) 682-3523
P/N:INFKAPCSOM
A NOTE ON POWER HANDLING
The speakers used in Kappa Series 2-Way
Component Systems are designed to produce rea-
sonable volume levels with little amplifier power.
However, the addition of an amplifier to drive
your speakers and a subwoofer will enhance the
dynamic range of your system, and help over-
come the ambient noise in a moving vehicle.
Kappa speakers are designed to handle the power
of a dedicated amplifier driven at or below its
rated power. If an amplifier is driven far above its
rated power, the output signal will “clip,” and the
additional power present in a clipped signal can
damage any speaker. Distorted or “fuzzy” sound
from your speakers is an indication that the ampli-
fier has exceeded its rated power, and you should
reduce the volume level.
GENERAL CARE
The loudspeaker grilles may be cleaned with a
slightly damp cloth. Do not use any cleaners or
solvents on the grilles or the speaker cones.
Kappa40.2/50.2/60.2/652.2csOM 1/5/00 11:11 AM Page 4