Filter
Top Products
SB-K-SL-12W0v2 INSTR_SKU# 011315
Page 3• JL Audio, Inc 2010
All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered
trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.
JLA-SKU# 011315 08.09.2010 • Printed in USA • ©2010 JL Audio, Inc. • U.S. PATENTS: #5,734,734 #5,949,898 #6,118,884 #6,229,902 #6,243,479
#6,294,959 #6,501,844 #6,496,590 #6,441,685 #5,687,247 #6,219,431 #6,625,292 #D472,891 #D480,709 Other U.S. & Foreign patents pending.
For more detailed information please visit us online at www.jlaudio.com.
(954) 443-1100
www.jlaudio.com
1 0 3 6 9 N O R T H C O M M E R C E P A R K W A Y • M I R A M A R , F L O R I D A • 3 3 0 2 5 • U S A
I N C L U D E D H A R D W A R E
1) 8mm x 38mm Coupling Nut 1) 8mm x 16mm Hex Cap Screw
3) 3/8-16 x 2-1/4” Allen Head Set Screw 3) 3/8-16 Hex Nut
3) 3/8” x 1-1/4” Fender Washer 3) 3/8” Split Lock Washer
3) 3” x 3” Wax Square 4) 1/4-20 x 1-1/2” Allen Head Bolt
2) 1/4-20 x 2” Phillips Flathead Screw 1) 5/16” Split Lock Washer
1) Custom Mount Strap
S P E C I F I C A T I O N S
Enclosure Type: Acoustic Suspension (sealed)
Driver Type: 12W0v2-4
Nominal Impedance: 4 Ohms
Continuous Power Handling: 300 Watts
P O W E R R E C O M M E N D A T I O N
JL Audio recommends high quality amplifiers such as the JL Audio XD400/4. The picture below shows the
recommended settings for the XD400/4. If another amplifier is being used, please reference this illustration and
use similar settings on that amplifier. All JL Audio amplifiers are very versatile audio components. Please consult
the owner’s manual for even more detailed information about installing and tuning your amplifier.
C O N N E C T I O N S
Using quality power, signal and speaker wire is essential in ensuring the performance of your Stealthbox®.
JL Audio recommends using a 4 AWG power kit such as the XC -PCS4-1B for your Stealthbox® amplifier, other
kits are available should you be using more than one amplifier. Signal wire such as the JL Audio Premium
Audio Interconnect Cables should be used that will provide signal for both channels of the amplifier. JL Audio
recommends using 12AWG speaker wire for subwoofers such as our XC-BCS12-25.
M I D / H I G H F R E Q U E N C Y D R I V E R F I T M E N T
A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.
Including a full Slampak® system designed for the Soul (SKU-94494)
Front/ Rear Speaker Size - Front Location: 6-1/2”- Front Doors
Fits JL Audio Models: TR650-CXi, C2-650x, C3-650, C5-650, C5-650x & ZR650-CSi
S T E P 1 5
C O N G R A T U L A T I O N S !
You have completed the installation for this model!
Enjoy your new Stealthbox®!
Please refer to the Power Recommendation section for an
amplifier recommendation and basic set-up help.
S T E P 1 4
If mounting an amplifier in the recess make sure to mount
the amplifier panel to the Stealthbox® first and then the amp
to the panel so that extra holes will not be drilled into the
Stealthbox®.
S T E P 1 3
The recess on the top of the Stealthbox® was specifically
designed to be a good mounting location for an amplifier.
The amplifier shown is the
JL Audio XD400/4. See
recommendations below if this is where the amp will be
mounted.
S T E P 1 2
Replace the tool kit that was removed in Step 2.