Filter
Top Products
2
A
Typical connections
ELECTRICAL CONNECTIONS
Rear line out (see diagram )
Rear ground terminal
15 A fuse
Black
Blue with white stripe
Red
Yellow
*
2
To the metallic body or chassis of the car
Ignition switch
Fuse block
To an accessory terminal in the fuse block
To the remote lead of other equipment (200 mA max.)
To a live terminal in the fuse block connecting to the car battery
(bypassing the ignition switch) (constant 12 V)
Antenna terminal
Blue
To the automatic antenna if any (250 mA max.)
Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this unit.
The leads of the power cord and those of the connector from the car body may be different in color.
1 Connect the colored leads of the power cord in the order specified in the illustration below.
2 Connect the antenna cord.
3 Finally connect the wiring harness to the unit.
*
1
Not supplied for this unit.
*
2
Before checking the operation of this unit prior to installation, this lead must be connected, otherwise the power
cannot be turned on.
To external components (see diagram
)
Connecting the external amplifier or subwoofer
B
You can connect an amplifier to upgrade your car stereo system.
• Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it can be controlled through this unit.
• Disconnect the speakers from this unit, connect them to the amplifier. Leave the speaker leads of this unit unused.
or
PurplePurple with black stripeGreenGreen with black stripeGrayGray with black stripeWhiteWhite with black stripe
Right speaker (rear)Left speaker (rear)Right speaker (front)Left speaker (front)
Y-connector (not supplied for this unit)Remote lead
Subwoofer
Rear speakers
JVC Amplifier
JVC Amplifier
Set “L/O MODE” to “SUB.W” (See page 22 of the
INSTRUCTIONS.)
Set “L/O MODE” to “REAR” (See page 22 of the
INSTRUCTIONS.)
Front speakers
Signal cord (not supplied for this unit)
Remote lead (blue with white stripe)
To the remote lead of other equipment or
automatic antenna if any
C
Connecting the external components
When connecting the external components, refer also to the manuals supplied for the components and
adapter.
CAUTION:
Before connecting the external components, make sure that the unit is turned off.
You can connect the following JVC components to the CD changer jack.
JVC component Model name
CD changer (CD-CH) CH-X1500, etc.
You can also connect the following components through the various JVC adapters.
• Connection cords may need to be purchased separately.
Component Adapter Model name
Bluetooth device Bluetooth adapter KS-BTA200
iPod Interface adapter for iPod KS-PD100
Portable audio player with line output jacks Line input adapter KS-U57
Portable audio player with 3.5 mm stereo mini jack AUX input adapter KS-U58
CD changer jack
When connecting two components in series
A KS-BTA200
B *
4
CD-CH / KS-PD100 / KS-U57 / KS-U58
To disconnect the connector
Hold the connector tightly ( 1 ), then pull it out ( 2 ).
iPod is a trademark of Apple Inc., registered in the U.S. and other countries.
*
4
*
3
Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place uncoated with paint
(if coated with paint, remove the paint before attaching the wire). Failure to do so may cause damage to the unit.
*
4
To use these components, set the external input setting correctly (see page 22 of the INSTRUCTIONS).
When connecting more than one component (maximum: two), it is recommended that you connect
the components in series as explained below.
Install1-2_KD-R404[UI]f.indd 2Install1-2_KD-R404[UI]f.indd 2 9/9/08 11:36:14 AM9/9/08 11:36:14 AM