Jwin JC-CD160 Car Stereo System User Manual


  Open as PDF
of 4
 
-- 5 --
-- 4 --
23.RANDOM BUTTON (RDM)
Press the key. Tracks will be player in randomorder.
To cancel the function the press the key again.
19.TRACK/SEARCH BUTTON
FORWARD AND REVERSE TRACK SEARCH
Press the SKIP button or during play to go to the desired track(song).
( ....REVERSE)(
....FORWARD)
Press and hold the SKIP button or during play to scan the disc at high speed.When the
desired music section of the disc is found,release the button.Normal play will resume.
20.PAUSE BUTTON
During PLAY ,press button to PAUSE.Press it again to resume play.
21.INT BUTTON (Priview all Tracks)
This feature allowes you to listen to the first 10 seconds of each track on the
display .Press the key SCAN indicator appears on the LCD pannel.
To cancel the function press the key again.
To repeat the current track press the key.The RPT indicator appears on the LCD
panel and the track be repeated continuously.
To cancel the function press the key again.
22.REPEAT BUTTON (RPT)
17.CD EJECT BUTTON
Press the EJECT button to remove the CD.The receiver will automatically switch to radio mode.
DISPDISP RPTRPT RDMRDM SCANSCAN
ALLALL DIRDIR
SONGSONG
MUSICMUSIC
MUTEMUTE
LOUDLOUD
MONOMONO
AFAF
PTYPTY EONEON
JAZZJAZZ
CLASSICCLASSIC
L
U
D
L
U
D
SCN
3RPT
4RDM
5
6
MODE
BND MUT
CLK
ST
LOC
LUD
L
UD
1
A/PS
2INT
L
E
S
H
S
U
P
60 WATT/DIGITAL TUNING SYSTEM
C D / C D - R / C D - R W P L A Y E R
18
17
19
20
21
23
22
CD CONTROL LOCATION OF PARTS
18.CD SLOT
1. Press the release button and pull-off the front panel.
2. To install the front panel, insert the panel into the housing and make sure the panel is securely
installed, otherwise, abnormalities occurs on the display or some keys will not function properly.
HOW TO REMOVE AND INSTALL THE FRONT PANEL
PRECAUTIONS
PRECAUTIONS WHEN HANDLING THE FRONT PANEL
Do not touch the contacts on the front panel or on the unit body, since this may result
in poor electrical conductivety.If dirt or other foreign substances get on the contacts, wiper
them with a clean dry cloth.
Do not leave the front panel in any area exposed to high temperatures or direct sunlight.
Do not drop the front panel or otherwise subject it to strong impact.
Do not allow such volatile agents as benzene, thinner, or insecticides to come into contactwith the
surface of the front panel.
Never try to disassemble the front panel.
Front Panel
Release Button
INSTALLING THE FRONT PANEL
REMOVING THE FRONT PANEL
Choose the mounting location where the unit will not interfere with normal driving function.
Before finally installing the unit, connect the wiring temporarily and make sure it is all connected
up properly and the unit and the system work properly.
Use only the parts included with the unit to ensure proper installation. The use of unauthorized
parts can cause malfunctions.
Consult with your nearest dealer if installation requires the drilling of holes or other modifications
of the vehicle.
Install the unit where it does not get in the driver s way and cannot injure the passenger if there
is a sudden stop. Like an emergency stop.
If installation angle exceeds 30 from horizontal the unit might not give optimum performance.
Avoid installating the unit where it would be subject to high temperature.such as from direct
sunlight. Lower case or from hot air,from the heater,or where it would be subect to dust,.dirt or
excessive vibration.
INSTALLATION
NOTE:
DIN FRONT/REAR-MOUNT
This unit be can properly installed either from Front (conventional DIN Front-mount) or Rear
(DIN Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis). For
detail, refer to the following illustrated installation methods.
 previous