Filter
Top Products
English
|
31
2nd section
Multi-function key operation
Audio setup item
[2]
"MEMORY"
[2] "USER"
[3] "INST"
User Memory
User Insttaller
[3]
"CALL"
[2] "USER"
[3] "INST"
Call User
Call Insttaller
• You can store an adjusted audio setup value by
selecting
"MEMORY". Also, you can recall it by
selecting "CALL". Refer to 'Audio Setup memory Recall'
(page 32).
3 Adjust the Audio setup item
Press the [4] or [¢] button.
Each time the button is pressed the setting
switches as shown below.
Adjustment Item Range
High Pass Filter Front
High Pass Filter Rear
High Pass Filter Center*
3
Through/30 — 250 (Hz)
Low Pass Filter Subwoofer 30 — 250 (Hz)
Subwoofer Phase setting Normal/ Reverse
DTA Front/DTA Rear/
DTA Subwoofer
0 — 610 (cm)
DTA Center*
3
0 — 170 (cm)
Bass Center Frequency 60 — 400 (Hz)
Middle Center Frequency 500 (Hz) — 3.15 (KHz)
Treble Center Frequency 4.00 (kHz) — 16.00 (KHz)
Bass Level/ Middle Level/
Treble Level
-9 — +9 dB
Bass Q Factor/ Middle Q Factor/
Treble Q Factor
0.25/ 0.50/ 1.00/ 2.00
SP-LEV Front Left/SP-LEV Front Right
SP-LEV Rear Left/SP-LEV Rear Right
SP-LEV Center*
3
/SP-LEV Subwoofer
-10 — +10
• The Adjustment item can also be controlled by the
rotary volume knob. Refer to 'Rotary Volume knob
operation mode select' (page 13).
• To get the best sound, first set the "CABIN" and "SP-
SEL" parameters using the 'Audio Setup (Easy mode)'
(page 28). Refer to 'Notes on Sound Management
System' (page 11).
• *
3
Function of the KDC-PSW9527
• When the 'Dual Zone System' (page 24) is ON, each of
the following setup is ignored.
- "X'over"/ "EQ" / "DTA"
4 Exit Audio setup mode
Press the [6] ("RTN") button.
Audio Setup Memory (PRO mode)
1
Selects the PRO mode of Audio setup
See the 'Audio Setup' (page 50) and select "Audio
Setup: PRO".
2 Select the source for adjustment
Press the [SRC] button.
3 Select the key function section
Press the [NEXT] button.
Repeatedly press the button until "AD SET" is
displayed above the [3] button.
Refer to 'Notes on Multi-function Key System'
(page 10).
4 Enter Audio Setup mode
Press the [3] ("AD SET") button.
5 Select the Adjustment item section
Press the [NEXT] button.
Repeatedly press the button until the desired
Adjustment item is displayed above the [2] — [5]
button.
6 Select the Audio Setup item for adjustment
Press the [2] — [5] button.
Adjust the audio setup by referring to the 'Audio
Setup (PRO mode)' (page 30).
7 Select the Memory item section
Press the [NEXT] button.
Repeatedly press the button until "MEMORY" is
displayed above the [2] button.
8 Select the Memory item
Press the [2] ("MEMORY") button.
9 Stores the adjusted audio setup value in
memory
Press the [2] ("USER")/ [3] ("INST") button for
at least 2 seconds.
The "MEMORY" display blinks 1 time.
"USER": The values are erased from memory if the
battery is removed or if the reset button
is pressed.
"INST": The values are held in memory even if the
battery is removed or if the reset button
is pressed.
10 Exit Audio Setup mode
Press the [6] ("RTN") button.