Kenwood KAC-829 Car Stereo System User Manual


  Open as PDF
of 2
 
System examples
L
R
L
R
L
R
L
R
L
R
L
R
L
R
MONO(Lch)
STEREO
OPERATION
MONO(Lch)
STEREO
L+R
OPERATION
KAC-829/729S/529S KAC-629S
LPF
FILTER
OFF
LPF
FILTER
HPF
OFF
L
R
L
R
MONO(Lch)
STEREO
OPERATION
MONO(Lch)
STEREO
L+R
OPERATION
KAC-829/729S/529S KAC-629S
LPF
FILTER
OFF
LPF
FILTER
HPF
OFF
MONO(Lch)
STEREO
OPERATION
MONO(Lch)
STEREO
L+R
OPERATION
KAC-829/729S/529S KAC-629S
LPF
FILTER
OFF
LPF
FILTER
HPF
OFF
7
8
7
8
7
8
7
8
7
8
7
8
POWER IN
BATT. P.CON(REMOTE)
GND
LEFT
BRIDGED
RIGHT
SPEAKER OUTPUT
POWER AMPLIFIER
432
Operations of the following control and switches
are required in accordance with the center unit
and speakers connected with this unit.
1 Fuse
40 A × 1 : KAC-829/729S
25 A × 1 : KAC-629S
15 A × 1 : KAC-529S
If you can’t find the specified capacity fuse at your
store etc., consult your Kenwood dealer.
2 Battery terminal
3 Ground terminal
4 Power control (REMOTE) terminal
5 SPEAKER OUTPUT terminals
• Stereo Connections:
When you wish to use the unit as a stereo
amplifier, stereo connections are used.
• Bridged Connections:
When you wish to use the unit as a high-output
monaural amplifier, bridged connections are
used. (Make connections to the LEFT channel (+)
and the RIGHT channel (–) SPEAKER OUTPUT
terminals.)
6 RCA cable ground lead terminal
When using an RCA cable with a ground lead
attached, connect the ground lead to this terminal.
Do not use this terminal for power source
grounding. This unit will be damaged if the power
source grounding wire is connected to this
terminal.
7 FILTER switch
These switches allow filtering of the speaker
output signals.
• HPF (High Pass Filter) position (KAC-
629S only)
Only frequencies of 150 Hz or higher are output.
(Frequencies below 150 Hz are cut.)
• LPF (Low Pass Filter) position
Only frequencies of 80 Hz or lower are output.
(Frequencies above 80 Hz are cut.)
The Lch and Rch will be mixed before output
even if the operation switch is set to STEREO.
• OFF position
The original sound without filtering is output.
8 OPERATION switch
This switch allows selection of the amplification
method of input signals.
• STEREO position
The amplifier can be used as a stereo amplifier.
• L+R position (KAC-629S only)
The input left and right signals are combined
before being amplified. Use this position when
the unit is used for subwoofer speakers or the
L+R (monaural) sound is required.
• MONO (Lch) position
Amplifies the signal input from the left side only.
Set to this position and make bridged
connections to use as a high-power monaural
amplifier. (The input right signal is not output.)
9 INPUT SENSITIVITY control
Set this control according to the pre-output level of
the center unit connected with this unit, or to the
maximum power output of the genuine-accessory
car stereo.
Use the diagram on the right as a guide.
For the pre-output level or the maximum power
output, refer to the “Specifications” in the
instruction manual of the center unit.
0 LINE IN terminal
! Speaker level input terminals
Power indicator
When the power is turned on, the Power indicator
lights.
If the Power indicator does not light when the power
is turned on, the protection function may be
activated. Check whether there is any indication of
trouble.
■ The protection function is activated
in the following situations:
This unit is equipped with a protection function for
protecting this unit and your speakers from various
accidents or problems that can occur.
When the protection function is triggered, the
Power indicator goes off and the amplifier stops
operating.
• When a speaker wire may be short-circuited.
• When a speaker output contacts ground.
• When the unit malfunctions and a DC signal is
sent to the speaker output.
• When the internal temperature is high and unit
won’t operate.
• When a ground wire of the center unit (cassette
receiver, CD receiver, etc.) or this unit is not
connected to a metal part serving as an electrical
ground passing electricity to the battery's
negative - terminal.
NOTE
2CAUTION
NOTE
Controls
40
FUSE(40A)
POWER IN
BATT. P.CON(REMOTE)
GND
LEFT
BRIDGED
RIGHT
SPEAKER OUTPUT
POWER AMPLIFIER
MONO(Lch)
STEREO
OPERATION
LPF
OFF
FILTER
L R
LINE IN
LEFT RIGHT
SPEAKER LEVEL INPUT
GND
INPUT
SENSITIVITY(V)
MAXMIN
0.30.5
1.0
25
FUSE(25A)
POWER IN
BATT. P.CON(REMOTE)
GND
LEFT
BRIDGED
RIGHT
SPEAKER OUTPUT
POWER AMPLIFIER
MONO(Lch)
STEREO
OPERATION
LPF
HPF
FILTER
L R
LINE IN
LEFT RIGHT
SPEAKER LEVEL INPUT
GND
INPUT
SENSITIVITY(V)
MAXMIN
0.30.5
1.0
OFF L
+
R
STEREO
/
BRIDGEABLE
AMPLIFIER
KAC-829
MAXIMUM POWER
STEREO
/
BRIDGEABLE
AMPLIFIER
INPUT
SENSITIVITY(V)
MAXMIN
0.30.5
1.0
(W)
20
15
10
9
1 0234 895 !6
1234 5
7
089 !6 7
KAC-629S
KAC-529S
KAC-829
KAC-729S
KAC-629S
KAC-829
KAC-729S
KAC-529S
Power indicator
KAC-829
KAC-729S
KAC-629S
KAC-529S
Terminal cover
Battery
Ground wire*
Battery wire*
Protective Fuse*
Power control wire*
■ Power wire connection
L
R
L
R
L
C
C
MONO(Lch)
STEREO
OPERATION
MONO(Lch)
STEREO
L+R
OPERATION
KAC-829/729S/529S KAC-629S
LPF
FILTER
OFF
LPF
FILTER
HPF
OFF
7
8
7
8
Connection
For safe installation, read "Installation procedure" before starting work.
NOTE
POWER IN
BATT. P.CON(REMOTE)
GND
LEFT
BRIDGED
RIGHT
SPEAKER OUTPUT
POWER AMPLIFIER
MONO(Lch)
STEREO
OPERATION
LPF
OFF
FILTER
L R
LINE IN
LEFT RIGHT
SPEAKER LEVEL INPUT
GND
INPUT
SENSITIVITY(V)
MAXMIN
0.30.5
1.0
POWER IN
BATT. P.CON(REMOTE)
GND
LEFT
BRIDGED
RIGHT
SPEAKER OUTPUT
POWER AMPLIFIER
MONO(Lch)
STEREO
OPERATION
LPF
OFF
FILTER
L R
LINE IN
LEFT RIGHT
SPEAKER LEVEL INPUT
GND
INPUT
SENSITIVITY(V)
MAXMIN
0.30.5
1.0
GND
LEFT
B
RID
GED
RIGHT
LEFT
BRIDG
ED
RIGHT
L
E
F
T
R
IG
H
T
SPEAKER LEVEL INPUT
4
6!
5
5
4
CENTER UNIT (Cassette receiver,
CD receiver, etc.)
Power control wire*
RCA cable*
Genuine-accessory car stereo (No
line output center unit etc.)
ACC
Battery
Car fuse box
Lead terminal*
Subwoofer
Lead terminal*
Right speaker
Left speaker
Speaker
■ 2-channel system
■ 1-channel system
■ Subwoofer system
■ RCA cable connection ■ Speaker level input connection
■ Speaker stereo connection ■ Speaker bridge connection
CENTER
UNIT
CENTER
UNIT
CENTER
UNIT
■ Tri-mode
Principle of Tri-mode
Method of frequency band division using a coil
and capacitor ... in case of 6dB/oct. slope
Coil (L): Passes low frequencies and blocks
high frequencies. (Low pass)
Capacitor (C): Passes high frequencies and
blocks low frequencies. (High pass)
Example:
When it is required to set a crossover
frequency of 120 Hz using speakers with an
impedance of 4 ohms.
fc=Cut of Frequency (Hz)
R=Speaker Impedance (Ω)
• If you wish to bridge-connect a speaker, the
speaker impedance must be no less than 4
ohms. Connecting a speaker with an
impedance lower than 4 ohms may damage
the unit.
• Be sure to connect capacitors to speakers to
which high frequencies will be passed.
Failure to do so will result in a drop of the
combined impedance with the subwoofer.
• Ensure that the withstand voltage and
current ratings of the capacitors (C) and coils
(L) are sufficient.
2CAUTION
L
C
0 dB
-3 dB
Crossover Frequency
Frequency
CENTER
UNIT
High pass
Subwoofer
(L + R)
159000
C= (µF)
fc x R
159 x R
L= (mH)
fc
159000
= = 331.25 µF
120Hz x 4Ω
159 x 4Ω
= = 5.3 mH
120Hz
Left speaker
Right speaker
Left speaker
Right speaker
Left speaker
Right speaker
Subwoofer
Lead terminal*
*…Commercially available parts
25W or greater
KAC-8_529(KE-10)1En 02.12.16 11:25 AM Page 2
 previous