Filter
Top Products
16
Specifications
■
PANEL
Screen Size 8.4” Diagonal
Display Area (h x v) 170.4 x 127.8 mm
Aspect Ratio 4:3 Native (4:3/16:9 Modes)
Pixels 800 x RGB x 600
Color Depth 24-bit (16,777,216 Colors)
Viewing Angle (h x v) 160° x 140°
Brightness 650 cd/m
2
Contrast Ratio 600:1
Dot Pitch (h x v) 0.071 x 0.213 mm
Pixel Pitch (h x v) 0.213 x 0.213 mm
Pixel Response 25 ms (rise + fall)
■
VIDEO INPUT/OUTPUT
Video Input / Output
Supports SMPTE 170M, NTSC/PAL
S-Video (Y/C) Input / Output
Supports SMPTE 170M, NTSC/PAL
YP
B
P
R
Input / Output
Supports SMPTE 260M, 274M, 296M
HD-SDI Input / Output
Supports ITU-R BT.656, SMPTE 259M, 292M
VGA Input
Supports RGBHV, RsGsBs, RGsB, RGB CS
DVI Input
Supports Digital Signals Only (DVI-D)
HDMI, HDCP Supported
■
CONNECTORS
Video Input
Video 1 x BNC Female (75 Ω)
S-Video (Y/C) 1 x 4-Pin Mini-DIN
YP
B
P
R
3 x BNC Female (75 Ω)
HD-SDI 1 x BNC Female (75 Ω)
VGA 1 x HD-15 Female
DVI 1 x DVI-I 29-Pin Female
Video Output (Active Loop-Through)
Video 1 x BNC Female (75 Ω)
S-Video (Y/C) 1 x 4-Pin Mini-DIN
YP
B
P
R
3 x BNC Female (75 Ω)
SDI 1 x BNC Female (75 Ω)
Power Input
4-Pin XLR Male
Tally Interface
HD-15 Female
■
TALLY
3 LEDs (Green, Red, Yellow). Activation requires contact
closure of pin to ground on the HD-15 connector:
Pin No. Signal
1 Green
2 Red
3 Yellow
4 Ground
5 Ground
6 N/C
7 N/C
8 N/C
9 N/C
10 N/C
11 N/C
12 N/C
13 N/C
14 N/C
15 N/C
■
ELECTRICAL
Power Consumption 2A @ 12VDC (24 W)
Voltage Requirement 12 VDC
V-PS12-5V-XLR Power Supply:
Input 100V-240V, 1.5A, 50-60Hz
Output 12VDC, 5A, 60W Max
V-Mount Battery Adapter
(Accepts standard 12V / 14.4V V-Mount Batteries)
■
MECHANICAL
Dimensions (w x h x d): 9.00” x 7.00” x 1.87”
Additional Mounting: Desktop Stand and Rack Adapter
Available
Weight (Monitor Only): 2.8 lbs
Operating Temperature 32°F to 120°F (0°C to 50°C)
Storage Temperature -4°F to120°F (-20°C to 50°C)
Compliance ₠, FCC-Class A, ANSI-63.4
(Certificates on file)
RoHs Do not dispose. Return to
Manufacturer or Authorized
Recycle Facility.
5
Installation and Initial Setup
■
Unpacking
Carefully unpack the V-LCD84SB-AFHD monitor and verify that the following items are included:
• V-LCD84SB-AFHD Monitor
• V-PS12-5V-XLR Power Supply with 4-Pin XLR Connector
• Operating Instructions
Inspect the unit for any physical damage that may have occurred during shipping. Should there be any damage,
immediately contact Marshall Electronics at (800) 800-6608. If you are not located within the continental United States,
call +1 (310) 333-0606.
■
Installation
The V-LCD84SB-AFHD monitor is shipped with a ¼”-20 mounting bracket on the bottom side, allowing the monitor to
be flexibly mounted to a camera or other device using a variety of mounts. This ¼”-20 mounting bracket can also be
attached to any side of the monitor.
Alternately, the V-LCD84SB-AFHD can be used in a desktop configuration with optional stands (Marshall part numbers
V-ST08 and V-STA84), or mounted in 19” inch rack with optional adapter (Marshall part number V-FR84).
■
Connections and Power-On
Plug the V-PS12-5V-XLR power supply into an AC power source (100-240 V @ 50/60 Hz). Attach the 4-pin XLR
connector to the back of the monitor. Please note that 12VDC can be also supplied directly to the monitor from a
variety of sources. The monitor will draw approximately 2 Amps at 12 Volts in operation.
Connect the required cables for video signal input and output. (Power must be applied to the V-LCD84SB-AFHD for
the active loop-though outputs to be activated.) All BNC connectors are rated at 75Ω.
Turn on the unit by pressing the power button located on the front panel. Select a video input by pressing the
corresponding input select button.
V-LCD84SB-AFHD with optional desktop stand (Marshall Part Number V-ST08)
¼”-20 Mounting Bracket
can also be attached to
any side of the
monitor