Filter
Top Products
16
Specifications
■
PANEL
Screen Size 9.0” Diagonal
Display Area (h x v) 196.8 x 118.08 mm
Aspect Ratio 16:9 Native (4:3/16:9 Modes)
Pixels 800 x RGB x 480
Color Depth 24-bit (16,777,216 Colors)
Viewing Angle (h x v) 160° x 140°
Brightness 400 cd/m
2
Contrast Ratio 600:1
Dot Pitch (h x v) 0.082 x 0.246 mm
Pixel Pitch (h x v) 0.246 x 0.246 mm
■
VIDEO INPUT/OUTPUT
Video Input / Output
Supports SMPTE 170M, NTSC/PAL
S-Video (Y/C) Input / Output
Supports SMPTE 170M, NTSC/PAL
YP
B
P
R
Input / Output
Supports SMPTE 260M, 274M, 296M
HD-SDI Input / Output
Supports ITU-R BT.656, SMPTE 259M, 292M
VGA Input
Supports RGBHV, RsGsBs, RGsB, RGB CS,
DVI Input
Supports Digital Signals Only (DVI-D)
HDMI, HDCP Supported
■
CONNECTORS
Video Input
Video 1 x BNC Female (75 Ω)
S-Video (Y/C) 1 x 4-Pin Mini-DIN
YP
B
P
R
3 x BNC Female (75 Ω)
HD-SDI 1 x BNC Female (75 Ω)
VGA 1 x HD-15 Female
DVI 1 x DVI-I 29-Pin Female
Video Output (Active Loop-Through)
Video 1 x BNC Female (75 Ω)
S-Video (Y/C) 1 x 4-Pin Mini-DIN
YP
B
P
R
3 x BNC Female (75 Ω)
SDI 1 x BNC Female (75 Ω)
Power Input
4-Pin XLR Male
Tally Interface
HD-15 Female
■
TALLY
3 LEDs (Green, Red, Yellow). Activation requires contact
closure of pin to ground on the HD-15 connector:
Pin No. Signal
1 M1 Green
2 M1 Red
3 M1 Yellow
4 Ground
5 Ground
6 N/C
7 N/C
8 N/C
9 N/C
10 N/C
11 M2 Green
12 M2 Red
13 M2 Yellow
14 Ground
15 Ground
■
ELECTRICAL
Power Consumption 2.5A @ 12VDC (30 W)
Voltage Requirement 12 VDC
V-PS12-5V-XLR Power Supply:
Input 100V-240V, 1.5A, 50-60Hz
Output 12VDC, 5A, 60W Max
V-Mount Battery Adapter
(Accepts standard 12V / 14.4V V-Mount Batteries)
■
MECHANICAL
Dimensions (w x h x d): 18.98” x 6.92” x 1.76”
Weight (Monitor Only): 6.40 lbs
Operating Temperature 32°F to 120°F (0°C to 50°C)
Storage Temperature -4°F to120°F (-20°C to 50°C)
Compliance ₠, FCC-Class A, ANSI-63.4
(Certificates on file)
RoHs Do not dispose. Return to
Manufacturer or Authorized
Recycle Facility.
5
Installation and Initial Setup
■
Unpacking
Carefully unpack the V-R902DP-AFHD monitor and verify that the following items are included:
• V-R902DP-AFHD Monitor
• V-PS12-5V-1 Power Supply with 2-Pin Twist Lock Connector
• Operating Instructions
Inspect the unit for any physical damage that may have occurred during shipping. Should there be any damage,
immediately contact Marshall Electronics at (800) 800-6608. If you are not located within the continental United States,
call +1 (310) 333-0606.
■
Installation
The V-R902DP-AFHD can be mounted in any standard EIA 19” equipment rack. The included rack mount adapter
brackets can be angled up to 110 degrees to provide the user full control over the viewing angle. Adequate ventilation
is required when installed to prevent possible damage to the monitor’s internal components.
■
Connections and Power-On
Plug the V-PS12-5V-1 power supply into an AC power source (100-240 V @ 50/60 Hz). Attach the 2-pin twist lock
connector to the back of the monitor. Please note that 12VDC can be also supplied directly to the monitor from a
variety of sources. The monitor will draw approximately 2.5 Amps at 12 Volts in operation.
Connect the required cables for video signal input and output. (Power must be applied to the V-R902DP-AFHD for the
active loop-though outputs to be activated.) All BNC connectors are rated at 75Ω.
Turn on the unit by pressing the power button located on the front panel. Select a video input by pressing the
corresponding input select button.
Rack Mount
Adapter Bracket