Filter
Top Products
+12V GND
POWER
SPEAKER
REM
+
-
+
-
+12V GND
POWER
SPEAKER
REM
+
-
+
-
DUAL VOICE COIL
SUBWOOFER /
AMPLIFIERS NOT
LINKED
30th ANNIVERSARY
GROUND POUNDER
30th ANNIVERSARY
GROUND POUNDER
30th ANNIVERSARY
GROUND POUNDER
PARALLEL MONO
SUBWOOFERS
2 OHMS EACH MINIMUM
+12V GND
POWER
SPEAKER
REM
+
-
+
-
8
SINGLE AMP INSTALLATION PROCEDURE:
1. Connect the amp LINE INPUTS to the Radio/CD player full range or mono line out
puts with good quality RCA interconnect cables.
2. Plug in the GPR-1 bass remote module into the amp REMOTE INPUT jack.
3. Route a 0 gauge power cables directly to the vehicle battery with an in-line fuse.
4. Connect a 0 gauge ground cables directly to chassis ground with in 36” of the amp.
- Be sure to remove any paint or primer from the ground point.
- Use a nut, bolt and lock washer to secure the ground cable to the chassis ground.
5. Connect the subwoofer(s) in accordance to the diagrams below.
6. Make sure the MASTER/SLAVE switch is in the MASTER position.
Note: The amplifier will not work if the MASTER/SLAVE switch is in the Slave position
DUAL AMP INSTALLATION PROCEDURE:
5. Connect two 0 gauge ground cables directly to the chassis with in 36” of the amp.
1. Connect the amp LINE INPUTS to the Radio/CD player full range or mono line out
- Be sure to remove any paint or primer from the ground point.
puts with good quality RCA interconnect cables.
- Use a nut, bolt and lock washer to secure the ground cable to the chassis ground.
2. Plug in the GPR-1 bass remote module into the amp REMOTE INPUT jack. This will
6. Make sure the Master amp MASTER/SLAVE switch is in the MASTER position.
allow the Master amp to control both Master and Slave amps with just one Remote..
Make sure the Slave amp MASTER/SLAVE switch is in the SLAVE position.
3. Connect an RCA jumper cable from the Master amp MASTER OUTPUT to the
7. Connect the subwoofer(s) in accordance to the diagrams below.
Slave amp SLAVE INPUT. Note: This will “link” the amps so that the Master amp
8. Connect a 12 gauge jumper from Master amp speaker - to Slave amp speaker - as
crossover switches will control both the Master and Slave amps. The Slave amp
shown below.
crossover switches will be bypassed.
4. Route two 0 gauge power cables directly to the vehicle battery with an in-line fuse.
FULL RANGE
STEREO LINE INPUT
NOT USED
Y-ADAPTOR
Note: You can use the Radio/CD designated mono line output
or a full range stereo line output. For full range stereo line
output, you will need an optional “Y-Adaptor” as shown.
GPV3000.1D PRO D CLASS 1 CHANNEL AMPLIFIER APPLICATIONS
Basic application
DESIGNATED
MONO OUTPUT
FROM HEAD UNIT
MONO
SUBWOOFER
OUTPUT
MASTER
INPUT
SLAVE
IN
OUT
L
R
L
R
15 35Hz 0dB 10dB 35 250Hz 0 180 9V 0.2V PRO
INPUT OUTPUT BALANCED SUBSONIC BASS EQ REMOTE LOW PASS PHASE LEVEL PWR
INPUT
MIN MAXX
GPR-1
REMOTE TURN-ON
CHASSIS GROUND
TO BATTERY + 12 Volts
VIA FUSE
+12V GND
POWER
SPEAKER
REM
+
-
+
-
Linking two amps for single or dual subwoofer application
MASTER
SLAVE
DESIGNATED
MONO OUTPUT
FROM HEAD UNIT
SINGLE REMOTE,
CONNECTED TO MASTER
AMP, USED TO CONTROL
BOTH AMPS WHEN LINKED
OUTPUT
MASTER
INPUT
SLAVE
IN
OUT
L
R
L
R
15 35Hz 0dB 10dB 35 250Hz 0 180 9V 0.2V PRO
INPUT OUTPUT BALANCED SUBSONIC BASS EQ REMOTE LOW PASS PHASE LEVEL PWR
INPUT
MIN MAXX
GPR-1
SPEAKER
REM
+
-
+
-
OUTPUT
MASTER
INPUT
SLAVE
IN
OUT
L
R
L
R
15 35Hz 0dB 10dB 35 250Hz 0 180 9V 0.2V PRO
INPUT OUTPUT BALANCED SUBSONIC BASS EQ REMOTE LOW PASS PHASE LEVEL PWR
INPUT
+12V GND
+12V GND
POWER
POWER
SPEAKER
REM
+
-
+
-
SUBWOOFER
12 GAUGE JUMPER WIRE
RCA JUMPER CABLE
MASTER OUTPUT TO SLAVE INPUT
Amplifiers are stable to 2ohms when linked
OUTPUT
MASTER
INPUT
SLAVE
OUTPUT
MASTER
INPUT
SLAVE
+12V GND
POWER
SPEAKER
REM
+
-
+
-
+12V GND
POWER
SPEAKER
REM
+
-
+
-
TWO SUBWOOFERS /
TWO AMPLIFIERS
NOT LINKED
- +
- +