Filter
Top Products
© 2011 Phoenix Gold • www.phoenixgold.com
Amplier Owner’s Manual
RMS Power 14.4Vdc ≤1% THD 80 x 4 @ 4 ohms Stereo
125 x 4 @ 2 ohms Stereo
250 x 2 @ 4 ohms Bridged
plus
500 x 1 @ 4 ohms
800 x 1 @ 2 ohms
Dynamic Power 14.4Vdc >1% THD 95 x 4 @ 4 ohms Stereo
150 x 4 @ 2 ohms Stereo
300 x 2 @ 4 ohms Bridged
plus
700 x 1 @ 4 ohms
1000 x 1 @ 2 ohms
Recommended Fuse Size: 100 amp
Power/Ground Wire Size: 4 Gauge
Dimensions (Includes Mounting Feet): 14.33” L x 6.93” W x 2.0” H
364mm L x 176mm W x 51mm H
Dimensions (Includes Terminals): 14.96” L x 6.93” W x 2.0” H
380mm L x 176mm W x 51mm H
RMS Power 14.4Vdc ≤ 1% THD 900 x 1 @ 2 ohms
1300 x 1 @ 1 ohm
Dynamic Power 14.4Vdc >1% THD 1200 x 1 @ 2 ohms
1600 x 1 @ 1 ohm
Recommended Fuse Size: 120 amp
Power/Ground Wire Size: 4 Gauge
Dimensions (Includes Mounting Feet): 14.33” L x 6.93” W x 2.0” H
364mm L x 176mm W x 51mm H
Dimensions (Includes Terminals): 14.96” L x 6.93” W x 2.0” H
380mm L x 176mm W x 51mm H
INPUT
Connect preamp signal cables from the head unit to these terminals.
CROSSOVER FREQUENCY
Controls the lowpass crossover point for the speaker outputs.
BASS BOOST
Variable bass boost from 0 to +18dB @ 45Hz.
REMOTE LEVEL CONTROL
This port is for connecting the subwoofer remote level control. This allows
up to 20dB of volume adjustment. This is not a bass boost, it controls the
level of the low pass signal.
NOTE: This control is not compatible with the Phoenix Gold LPL44 level
control.
SENS
Used to reach maximum amplier power with a wide variety of headunits.
SUBSONIC CROSSOVER FREQUENCY
Controls the highpass crossover point for the speaker outputs to eliminate
extreme low frequencies.
RMD
Optional RMD Voltage Display plugs into this port. Sold separately.
+12V
This must be connected to the fused positive terminal (+12V) of the car’s
battery. The fuse must be located within 18 inches of the battery.
REMOTE
This must be connected to switched +12V, usually a trigger wire coming
from the head unit or ignition.
GROUND
This must be connected to the negative terminal of the car’s battery or
bolted to a clean, unpainted part of the chassis of the vehicle.
SPEAKER OUTPUTS
Used to connect the amplier to speakers. SD1300.1 minimum impedance
is 1 ohm.
SD1300.1
Monoblock Power Amplifier
NOTE: Visible through the plexiglass cover, a single blue power LED is located in the lower corner of all SD ampliers.
GROUND REMOTE + 12V
GROU ND + 12VR
FUSE
40A40A
40A
POWER
SENS
MIN MAX
BASS
0dB 18dB
X-OVER
FREQ.
30Hz 300Hz
REMOTE
PROTECT
SUBSONIC
10Hz 55Hz
L
R
INPUT
RMD
SPEAKER
PROTECT
POWER
REMOTE
SUB INPUT
R
MIN MAX
MIN MAX
SENS
SENS BASS BOOST
0dB 18dB
HPF
15Hz 250Hz
HPF
15Hz 250Hz MIN MAX
SENS
30Hz
LPF
300Hz
GROUND REMOTE + 12V
FL
SUB.
SUB.
INPUT
RR
RL
FR
FL
SUB INPUT
L
SUB FRONT
FRONT REAR
FR
RL RR
GROU ND + 12VR
RMD