Filter
Top Products
Installation English
Note
• Check all connections and systems before final
installation.
• Do not use unauthorized parts. The use of
unauthorized parts may cause malfunctions.
• Consult with your dealer if installation requires
drilling of holes or other modifications of the
vehicle.
• Do not install this unit where:
— it may interfere with operation of the vehicle.
— it may cause injury to a passenger as a result of
a sudden stop.
• The semiconductor laser will be damaged if it
overheats. Install this unit away from hot places
such as near the heater outlet.
• Optimum performance is obtained when the unit
is installed at an angle of less than 60°.
60°
DIN Front/Rear-mount
This unit can be properly installed either from
“Front” (conventional DIN Front-mount) or
“Rear” (DIN Rear-mount installation, utilizing
threaded screw holes at the sides of unit
chassis). For details, refer to the following
installation methods.
DIN Front-mount
Installation with metal strap and
screws
1. Insert the mounting sleeve into the
dashboard.
• When installing in a shallow space, use a
supplied mounting sleeve. If there is enough
space behind the unit, use factory supplied
mounting sleeve.
2. Secure the mounting sleeve by
using a screwdriver to bend the
metal tabs (90°) into place.
Dashboard
Mounting sleeve
53
182
3. Install the unit.
• Use commercially available parts when
installing.
Screw (M48)
Screw
Metal strap
Nut
Firewall or
metal support
• Make sure that the unit is installed securely
in place. Unstable installation may cause this
unit to malfunction, such as sound skip.
Removing the Unit
1. Extend top and bottom of the trim
ring outwards to remove the trim
ring.
When reattaching the trim ring,
push the trim ring onto the unit until
it clicks. (If the trim ring is attached
upside down, the trim ring will not
fit properly.)
• It becomes easy to remove the trim ring if the
front panel is released.
Trim ring
Installation English
2. Insert the supplied extraction keys
into both sides of the unit until
they click into place.
3. Pull the unit out of the dashboard.
DIN Rear-mount
1.
Extend top and bottom of the trim
ring outwards to remove the trim
ring. When reattaching the trim ring,
push the trim ring onto the unit until
it clicks. (If the trim ring is attached
upside down, the trim ring will not
fit properly.)
• It becomes easy to remove the trim ring if the
front panel is released.
Trim ring
2. Determine the appropriate position
where the holes on the bracket and
the side of the unit match.
3. Tighten two screws on each side.
• Use either truss screws (5 mm × 8 mm)
or flush surface screws (5 mm × 9 mm),
depending on the shape of screw holes in the
bracket.
Factory radio mounting bracket
Screw
Dashboard or Console
Fastening the front panel
If you do not plan to detach the front panel,
the front panel can be fastened with supplied
screw.
Screw
Conexión de las unidades
Español
Conexión de las unidades
Español
Cable USB CD-U150E Pioneer
(vendido separadamente)
50 cm
Puerto USB 2
Utilice un cabo USB para conectar el dispositivo
de almacenamiento USB al puerto USB 2.
El cable USB CD-U150E Pioneer también está
disponible. Para los detalles, consulte
su revendedor.
20 cm
iPod
Conector del Dock
Cable de interfaz
Amarillo/negro
Si se utiliza un equipo con función de
silenciamiento, conecte este conductor con el
conductor de silenciamiento de audio en tal
equipo. De lo contrario, mantenga el
conductor de silenciamiento de audio libre de
conexiones.
Amarillo
Conecte el terminal de suministro de 12 V
constante.
Rojo
Conecte al terminal controlado por del
interruptor de encendido (12 V CC).
Anaranjado/blanco
Conecte al terminal de interruptor de iluminación.
Negro (masa de la carrocería)
Conecte a un punto de metal limpio, libre de
pintura.
Este producto
Salida delantera
Toma de antena
Salida de altavoz
de subgraves
Fusible (10 A)
Salida trasera
Entrada IP-BUS (Azul)
Cable IP-BUS
Reproductor de
Multi-CD (vendido
separadamente)
Entrada remota por cable
Es posible conectar un adaptador
de mando a distancia por cable
(se vende por separado).
Blanco Gris
Gris/negroBlanco/negro
Verde Violeta
Verde/negro Violeta/negro
No se usa.
Conecte los cables
RCA (vendidos
separadamente)
A la salida del
altavoz de
subgraves
A la salida
delantera
A la salida
trasera
Control remoto de sistema
Azul/blanco
Conecte al terminal de control de sistema del
amplificador de potencia o al terminal de control de
relé de antena automática (máx. 300 mA 12 V CC).
Altavoz
delantero
Altavoz
delantero
Altavoz traseroAltavoz trasero
Altavoz de
subgraves
Altavoz de
subgraves
Amplificador de
potencia (vendido
separadamente)
Amplificador de
potencia (vendido
separadamente)
Amplificador de
potencia (vendido
separadamente)
Cuando conecte altavoces sin utilizar el amplificador interno
• Cuando utilice este sistema, se recomienda apagar el amplificador interno de esta unidad.
Para los detalles, consulte el manual de instrucciones.