Filter
Top Products
general features
PB317X
PB717X
PB1217X
2
23
High Performance 800Watt 2 channel
Bridgeable MOSFET Amplifier
High Performance 1000Watt 2 channel
Bridgeable MOSFET Amplifier
High Performance 1600Watt 2 channel
Bridgeable MOSFET Amplifier
400 Watts×2 Output
．
800 Watts×2 Output
．
500 Watts×2 Output
．
．
800 Watts×1 Bridged Output
．
1000 Watts×1 Bridged Output
．
1600 Watts×1 Bridged Output
．
．
．
．
．
．
．
．
．
．
．
．
．
．
Variable Hi/Lo Electronic Crossover Network
．
Variable Hi/Lo Electronic Crossover Network
．
Variable Hi/Lo Electronic Crossover Network
Variable Bass Boost(0-6-+12dB@60Hz)
．
．
Variable Input Level(Gain)Control
．
Variable Input Level(Gain)Control
．
Variable Input Level(Gain)Control
Remote Turn on/Off
．
Remote Turn on/Off
．
Remote Turn on/Off
RCA Inputs
．
RCA Inputs
．
RCA Inputs
High Level MOLEX Indicator
．
High Level MOLEX Indicator
．
High Level MOLEX Indicator
Power ON LED Indicator
．
Power ON LED Indicator
．
Power ON LED Indicator
LED Protection Indicator
．
LED Protection Indicator
．
LED Protection Indicator
S/N Ratio: >95dB
THD :<0.2%
Thermal Protection
Overload Protection
Short Circuit Protection
Anti-Thump Turn-On
．
．
．
．
．
．
S/N Ratio: >95dB
THD :<0.2%
Thermal Protection
Overload Protection
Short Circuit Protection
Anti-Thump Turn-On
．
．
．
．
．
．
S/N Ratio: >95dB
THD :<0.2%
Thermal Protection
Overload Protection
Short Circuit Protection
Anti-Thump Turn-On
mounting and installation
For this reason,
Your new PYRAMID Arctic Series amplifier comes complete with required mounting hardware.
When determining a suitable location in your vehicle for the amp, please remember that it is a high-
power electronic device capable of generating high heat.
always choose a location in your vehicle which has low
vibration,
About power fuses:
Be sure to mount the amp
Mark the location for the mounting screw holes by positioning the amp where you
wish to install
Then
mounting surface for the mounting screws and insert them. Tighten the screws securely.
Before attempting to drill the mounting holes, take
note of any wires, lines or otherdevices
in your vehicle which may be located behind the mounting surface!
Use at least 8 gauge wire for power and ground connections.
Wire the amplifier directly to the car battery.
For the ground connection, use the shortest possible wire to a good chassis
ground point.
Wire the Remote connection to the auto start lead of your head unit, equalizer or power antenna.
adequate
in such a manner as
ventilation, a minimum of dust, and no moisture.
to allow reasonable airflow over the cooling fins.
it and use a scribe (or one of the mounting
screws) inserted in each of the mounting holes to mark
the mounting surface for the mounting surface. If the mounting surface is carpeted, measure the
hole centers and mark with a felt tip pen.
drill pilot holes in the
When making electrical connections to your amplifier, please observe the following:
Pyramid Arctic Series amplifiers feature built-in fuse systems. These fuses protect both the
amplifier and the electrical system in your vehicle from fault conditions. If you ever need to replace
the fuse in your Pyramid Arctic Series amp, use a fuse of exactly the same type and rating. A
different
type or rating of fuse may result in damage or fire.
Variable Bass Boost(0-6-+12dB@60Hz)
Variable Bass Boost(0-6-+12dB@60Hz)