Filter
Top Products
Specifications
Specifications subject to change without notice.
WL2082-i WL118-sw
Configuration 3-way, bi-amp or tri-amp mode Vented box
Transducers
High-frequency Dual 50 W, 8Ω 1" exit, 1.75" titanium diaphragm, neodymium
magnet assembly
—
Low-frequency Dual 200 W, 16Ω 8" woofer, 2" voice coil, neodymium magnet
assembly, weather resistant cone
850 W, 8Ω 18" woofer with a 4" voice coil, ceramic
magnet assembly
Frequency Response (±3 dB) 80 Hz – 20 kHz 32 Hz – 200 Hz
Frequency Range (-10 dB) 68 Hz – 22 kHz 29 Hz – 800 Hz
Nominal Impedance HF: 16Ω
LF bi-amp mode: 8Ω
LF tri-amp mode: 16Ω (x 2)
—
—
LF: 8Ω
Continuous Power Capacity
1
/ Recommended Power HF: 100 W / 200 W
LF bi-amp mode: 400 W / 800 W
LF tri-amp mode: 200 W / 400 W (x 2)
—
—
LF: 850 W / 1750 W
Sensitivity (1 W at 1 m) HF: 106 dB
LF: 96 dB
—
LF: 98 dB
Maximum Output Continuous / Peak (SPL at 1 m) HF: 126 dB / 132 dB
LF: 122 dB / 128 dB
—
LF: 128.5 dB / 134.5 dB
Nominal Coverage H: 140°
V: dependent on number of elements used
—
—
Cabinet Type Ported, elliptical / trapezoidal Vented subwoofer
Enclosure Material HIPS (high impact polystyrene) with UV protectant 18 mm Baltic birch plywood
Finish Available in black (WL2082-i BLK) or white
(WL2082-i WHT) paintable
Available in black (WL118-sw BLK) or white
(WL118-sw WHT) paintable
Grille Perforated, formed aluminum 16 gauge powder-coated steel with cloth backing
Connectors 2 x NL8 in parallel 2 x NL8 in parallel / 2 x NL4 in parallel
Pin Outs Pins
1+/1-
2+/2-
3+/3-
4+/4-
Bi-Amp
NC
NC
LF
HF
Tri-Amp
NC
LF2
LF1
HF
Pins (NL8)
1+/1-
2+/2-
3+/3-
4+/4-
Sub
Pass thru
Pass thru
Pass thru
Pins (NL4)
1+/1-
2+/2-
Sub
Pass thru
Attachment Points Integral, side plate adjustable rigging system, vertical splay
adjustable in 1° increments from 0° – 10°
Integral, non-adjustable (straight array only)
Weight (Net / Shipping) 37 lb (16.8 kg) / 45 lb (20.45 kg) 111 lb (50.4 kg) / 121 lb (55 kg)
Dimensions (HWD) 11.8" x 27" x 13.4" (300 mm x 686 mm x 340 mm) 22.1" x 27.6" x 30.3" (562 mm x 702 mm x 771 mm)
Accessories Available FB2082-i: Fly-bar for WL2082-i, WL118-sw and WL115-sw. Available in black or white.
EB2082-i: Extension bar, allows WL118-sw or WL115-sw to be suspended behind WL2082-i. Available in black or white.
PB2082-i: Pullback bar for WL2082-i. For use when pulling back the bottom of the array is necessary to achieve the desired
angle. Available in black or white.
AB2082-i: Angle bracket, allows greater vertical splay between WL2082-i and WL118-sw or WL115-sw enclosures in ground
stacked configurations. Available in black. Requires two brackets per array, sold individually.
GS115-sw: Ground stack kit for WL118-sw or WL115-sw.
QRP-KIT-1: Kit of four (4) Quick Release Pins for use in lieu of included bolts.
1) 2 hours, IEC specified noise