Roadmaster VRS693 Car Speaker User Manual


  Open as PDF
of 1
 
INTERIOR PANEL
GRILL
SCREW
SPRING NUT
The small hole of
the spring nut is on
this side of panel
SPEAKER
WIRE
In a Precut HoleIn a Precut Hole
In an EnclosureIn an Enclosure
The placement of the speakers will vary from vehicle to vehicle. Most vehicles have factory
cut-outs on the rear window deck behind the rear seat, in the front doors, or front kick
panels. Before permanently installing the VRS693 speakers in your car, connect the wires to
the speakers according to your audio system’s installation manual, in the approximate
location you will install them. If you are satisfied with the location proceed with the
permanent installation.
Before you install the VRS693 speakers you must make sure
you have enough depth/space behind the mounting surface.
You do not want the back of the speaker magnet to touch any
part of your vehicle, or interfere with the operation or function
of any component in your vehicle. (ie. windows or trunk lid)
What if there is no sound?
Your stereo may have a blown fuse. Replace fuse with the same amperage and style.
You may have improper wiring. Refer to the wiring guide that came with your stereo/amplifier. Check
all wires for a secure connection.
What if the sound volume is low?
Your stereo may not have enough power. You may have to install an amplifier to drive the speakers.
Why do I have a whining noise coming from the speakers?
You may have poor filtering of your alternator. If that is the case, then you may need to add an
alternator filter to the power lead.
Why do I have odd sounding noises coming from the speakers?
You may have corroded battery terminals and/or a weak battery. If the terminals on the battery are
corroded, clean them; then check the sound. If the sound system is still making noises, then check
battery strength. If it is low, then recharge or replace the battery.
Why does the speaker have sound coming from one channel only?
First make sure the balance control is set correctly. If the balance is set correctly, your stereo may be
defective or the speaker may be defective. To troubleshoot this problem you MUST change both
positive and negative leads of each channel with the positive and negative leads of the opposite
channel. If the same speaker has no sound, then the speaker is no good. If the opposite speaker has
no sound, then your stereo may be defective.
You should only mount your speakers in factory precut holes. We DO NOT
recommend that you cut holes for mounting the speakers. If there are no
factory precut holes, consider having the speakers professionally installed.
1. Connect speaker wires.
2. Slip the spring nut(s) (provided)
into place and align the holes.
3. Place the speaker grill on the
speaker, then put the supplied
screws through the screw
holes of the speaker grill and
speaker. Align the screws with
screw holes of the spring nuts.
4. Tighten the screws, but not so
tight as to crack the plastic of
the speaker grills.
All auto audio components must be securely mounted. Driving styles
and road conditions such as sudden stops, sharp curves, and bumpy
roads may cause unsecured items to move about the vehicle, causing
physical injuries to vehicle occupants and/or vehicle damage.
• Nail Set/Center Punch
• Electrical Tape
3.5" or 7.9 cm
Automotive audio equipment installations can be troublesome at times, even to the most
experienced of installation technicians. If you are not confident working with electrical wiring,
removing and reinstalling interior panels, carpeting, dashboards or other components of your
vehicle, please call our toll-free help line 1-800-445-1797 and our in-house technical service
team will answer your installation questions.
Before permanently installing the VRS693 speakers in your car, connect the wires to the
speakers according to your audio system’s installation manual, in the approximate location you
will install them. If you are satisfied with the location, proceed with the permanent installation.
1 Pair VRS693
6" X 9" 3-Way Speakers
Read First!
Dear Customer,
CONGRATULATIONS.
The VRS693 6 3-way speakers, when used as described, will give you years of depend-
able service in your car, truck, RV, or mini-van. We have taken numerous measures in quality
control to ensure that your product arrives in top condition, and will perform to your satisfac-
tion. In the rare event that your VRS693 6 3-way speakers contains a damaged or miss-
ing item, does not perform as specified, requires warranty service, or you have an installation
problem,
DO NOT RETURN THIS PRODUCT TO THE STORE. PLEASE CALL OUR TOLL-
FREE NUMBER FROM THE U.S.A. AND CANADA 1-800-445-1797 and ask to speak with a
member of our technical service team, or submit your questions by e-mail to
customerservice@vr-3.com and a member of our technical service team will respond by e-mail
to your questions. Our in-house technical service team will expedite delivery of your part,
advise you on installation, or help troubleshoot a problem with you. If your product needs
warranty service, our technical service team representative will help you obtain the fastest
remedy possible under the warranty.
Tools Needed to Install
Before You Install
Specifications
Parts
1. Location of Speakers
2. Mounting The Speakers
3. Connecting The Wires
Frequently Asked Questions
Give Us A Call, We'll Help You Install
Limited Warranty
Notes
8 - Spring Nuts
8 - Screws
• Safety Glasses
• Electric Drill
with 1/16" bit
• Hammer
• Wire Cutter
• Phillips Screwdriver
• Marker
2 - 6" X 9" Speakers
2 - Speaker Grills
VIRTUAL REALITY SOUND LABS
®
products are designed and manufactured to provide a high level of trouble-free performance.
VIRTUAL REALITY SOUND LABS
®
warrants, to the original purchaser, that its products are free from defects in material and
workmanship for 30 days from the date of original purchase, as part of our commitment to product excellence VIRTUAL REALITY
SOUND LABS
®
and/or it’s affiliates routinely improves the designs, materials or production methods of its existing products. Because
it is impractical to publicize all changes in every product, we reserve the right to make such changes without notice.
CONDITIONS OF WARRANTY:
If during the 30 day warranty period your new product is found to be defective, VIRTUAL REALITY SOUND LABS
®
will repair such
defect, or replace the product, without charge for parts or labor subject to the following conditions:
1. All repairs must be performed by VIRTUAL REALITY SOUND LABS
®
and/or it’s affiliates in Eatontown, New Jersey.
2. The equipment must not have been altered or been damaged through negligence, accident, or improper operation.
3. The replacement of parts are exempted from this warranty when replacement is necessary due to normal wear and tear.
4. All warranty claims must be accompanied by a copy of the sales receipt or bill of sale.
5. Repair or replacement parts supplied by VIRTUAL REALITY SOUND LABS
®
under this warranty are protected only for the
unexpired portion of the original warranty.
6. In the case of car stereos, this warranty does not extend to the elimination of car static or motor noise; correction of antenna
problems; costs incurred for the removal or reinstallation of the product; damage to tapes, speakers, accessories or car electrical
systems.
7. VIRTUAL REALITY SOUND LABS
®
will not be responsible for any charge incurred for installation.
OWNER'S RESPONSIBILITIES:
VIRTUAL REALITY SOUND LABS
®
will make every effort to provide warranty service within a reasonable period of time.
SHOULD YOU HAVE ANY QUESTIONS ABOUT SERVICE RECEIVED, OR IF YOU WOULD LIKE ASSISTANCE IN OBTAINING
SERVICE, PLEASE CALL TOLL FREE 1-800-445-1797, 8:30am - 4:30pm EST.
In order to provide you with the proper warranty service, we request that you adhere to the following procedure:
1. Include a copy of your sales receipt or bill of sale with your unit when it is returned for warranty service.
2. If it is necessary to return your product for service, please return it securely packed, preferably in the original shipping carton, and
freight and insurance prepaid to the following address: VIRTUAL REALITY SOUND LABS, Service Department, 41 James Way,
Eatontown, New Jersey 07724.
3. Please include a detailed explanation of the problem you are having.
4. If your product is found by VIRTUAL REALITY SOUND LABS
®
to have a defect in material or workmanship, within the warranty
period, it will be repaired or replaced at no charge and returned to you prepaid. Where permitted by Iaw VIRTUAL REALITY SOUND
LABS
®
liability shall be limited to that set forth in this warranty. This warranty shall be the exclusive remedy of the purchaser.
VIRTUAL REALITY SOUND LABS
®
makes no other warranty of any kind, expressed or implied; and all implied warranties, are
hereby disclaimed by VIRTUAL REALITY SOUND LABS
®
and excluded from this warranty, VIRTUAL REALITY SOUND LABS
®
and/or it’s affiliates,
the manufacturer, distributor and seller shall not be liable for any injury, loss or damage, incidental or
consequential, arising out of the use or intended use of the product.
©2008
Intellectual Solutions Inc., All rights reserved. All designs, logos and images are the exclusive property of Intellectual
Solutions Inc. and/or it’s affiliates. US and Foreign Intellectual Property Rights Pending 071408 Printed in China 00000
PLEASE DO NOT RETURN PRODUCT TO STORE.
For Help Go To
WWW.VR-3.COM
For Information and Technical Assistance,
Call Toll-Free in U.S.A., Puerto Rico, and Canada.
1-800-445-1797
• 6” x 9" diecast aluminum basket .
• Black glass fiber wooven cone
• Buytl Rubber Surround
• 1.2" ASV 4 layers
• 24.6 Oz magnet
• Front Facing Cable-Free Tweeter
•
Hi performance 51mm PEI Midrange + 25 PEI Nd Tweeter
• Freqency Response : 40 - 20K Hz
• Sensitivity: 90dB/2.83V/1M (+/-3dB)
• Rms: 100 Watts Per Pair
• Max Pwr: 500 Watts Per Pair
• Impedance: 4Ω
To Strip Insulation from Wire:
When connecting the speaker wires to your speakers in a new installation, you should follow
the wiring instructions from your audio system’s manufacturer. For most systems, maintain
proper polarity by attaching the Positive Wire (+) to the Positive Terminal (+) and the Negative
Wire (-) to the Negative Terminal (-).
Strip a fingertip’s width
of insulation from end
of speaker cable. Twist
strands of wire together.
To Attach Wires to Terminals:
Speaker Terminals
Speaker Wire
1.
Push the speaker terminal
down as shown.
2. Insert a speaker
wire with about .25”
of insulation removed
from the end, then
release the terminal.
1. Place the speaker in the hole.
2.
Mark the speaker’s screw holes on the enclosure,
then remove the speaker from the hole.
3. Drill pilot holes where you have marked the
enclosure.
4. Connect the speaker wires.
5. Align the speaker with the holes, then insert the
screws and tighten.