Filter
Top Products
L
R
AUDIO OUT
T
O
P
TO
P
Installation
Precautions
•Do not tamper with the four holes on the upper surface of the unit. They are for tuner adjustments to be
done only by service technicians.
•Choose the installation location carefully so that the unit will not hamper the driver during driving.
•Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight or
hot air from the heater, or where it would be subject to dust, dirt, or excessive vibration.
•Use only the supplied mounting hardware for a safe and secure installation.
Mounting example
Installation in the dashboard
2
With the TOP marking up
Bend these claws, if necessary.
1
4
3
Dashboard
Fire wall
To support the unit
Mounting the unit in a Japanese car
You may not be able to install this unit in some makes of Japanese cars. In such a case, consult your Sony dealer.
TOYOTA NISSAN
to dashboard/center console
Bracket
to dashboard/center console
7 max. size 5 × 6 mm
(
7
/32 ×
1
/4 in.)
7 max. size 5 × 6 mm
(
7
/32 ×
1
/4 in.)
Note
To prevent malfunction, install only with the supplied screws 7.
1
3 max. size M4 × 6 mm
(
3
/16 ×
1
/4 in.)
2
4
Bracket
7 max. size 5 × 6 mm
(
7
/32 ×
1
/4 in.)
7 max. size 5 × 6 mm
(
7
/32 ×
1
/4 in.)
7
6
6
7
max. size 5 × 6 mm
(
7
/32 ×
1
/4 in.)
7
6
1
2
Bracket
Bracket
Existing parts supplied with your car
Mounting angle adjustment
Adjust the mounting angle to less than 60°.
1
10 mm (
13
/32 in.)
4 mm (
3
/16 in.)
90º
2
9
Insert the supplied tool 9 between the unit and the frame, and rotate 90° to
release the hidden mounting spring. Repeat on the opposite side and remove
the frame.
Insert a flathead screwdriver between the bracket and mounting spring. Gently
pry the spring toward the unit while pulling the unit out a little. Repeat on the
opposite side and remove the unit.
Removing the unit
1
Note
To prevent malfunction, install
only with the supplied screws 7.
Caution
•This unit is designed for negative ground 12 V DC operation only.
•Before making connections, disconnect the ground terminal of the car battery to avoid short circuits.
•Connect the yellow and red power input leads only after all other leads have been connected.
•Be sure to connect the red power input lead to the positive 12 V power terminal which is energized
when the ignition key is in the accessory position.
•Run all ground wires to a common ground point.
•Connect the yellow cord to a free car circuit rated higher than the unit’s fuse rating.
If you connect this unit in series with other stereo components, the car circuit they are connected to
must be rated higher than the sum of the individual component’s fuse rating.
If there are no car circuits rated as high as the unit’s fuse rating, connect the unit directly to the
battery.
If no car circuits are available for connecting this unit, connect the unit to a car circuit rated higher
than the unit’s fuse rating in such a way that if the unit blows its fuse, no other circuits will be cut
off.
•The use of optical instruments with this product will increase eye hazard.
Reset button
When the installation and connections are complete, be sure to press the reset button with a ball-point
pen, etc.
Parts for Installation and Connections
The numbers in the list are keyed to those in the instructions.
5
1
× 2
2
6
7
3
8
4
× 4
Caution
Cautionary notice for handling the bracket 1.
Handle the bracket carefully to avoid injuring your fingers.
9
Connection example
From car antenna
Red
Yellow
Black Blue/White
AUDIO OUT
8
TO
P
TO
P
Fuse
AMP REMOTE OUT
Max. supply current 0.3 A
REMOTE IN
Speaker system
Car audio
Antenna connector*
3
Rotary commander RM-X4S*
2
(not supplied)
Fuse
To a metal point of the car
First connect the black ground lead, then connect the yellow
and red power input leads.
To the +12 V power terminal which is energized at
all times
Be sure to connect the black ground lead first.
To the +12 V power terminal which is energized in
the accessory position of the ignition key
Be sure to connect the black ground lead first.
Existing parts supplied with your car
Reset button
DSPL
SHUF
AMS
REPEAT
OFF
Connections
0.5 m
(1 ft. 8 in.)
0.5 m
(1 ft. 8 in.)
0.5 m
(1 ft. 8 in.)
0.5 m
(1 ft. 8 in.)
1.9 m (6 ft. 3 in.)
0.5 m
(1 ft. 8 in.)
*
1
You can only connect a car audio which has both a remote
amplifier input (AMP REMOTE IN) and an audio input (AUDIO IN).
Note
Do not connect an external amplifier to the audio output (AUDIO
OUT) of this unit. Otherwise, the volume of the connected
speakers cannot be adjusted.
If you have a Sony car audio with the Sony BUS terminal, the optional source selector
XA-107 can be used in your system.
max. size 5 × 6 mm
(
7
/32 ×
1
/4 in.)
RCA pin cord
(not supplied)
To AUDIO IN
of the car audio*
1
To AMP REMOTE IN
of the car audio*
1
BUS CONTROL IN
AUDIO IN
AUDIO OUT
AUDIO IN
AUDIO OUT
MASTER
Sony car audio
Source selector
XA-107
CDX-1000RF
With the TOP marking up
5
*
2
You can also control the following functions with the rotary cammander
RM-X4S:
Power on – Press SOURCE.
Power off – Press OFF.
Locate a specific track
– Rotate the SEEK/AMS control momentarily and release.
Locate a specific point within a track
– Rotate the SEEK/AMS control and release when the desired point is found.
Adjust the volume – Rotate the volume control.
*
3
An adaptor (optional) may be necessary for your car and car audio system.
In such a case, consult your dealer.
182 mm (7
1
/
4
in.)
53 mm
(2
1
/
8
in.)
CDX-1000RF
Car audio with FM tuner
CDX-1000RF
Car audio with FM tuner