Filter
Top Products
06/04, MI 2200,
subject to modification
MI 2200
Multimedia Interface
Automatic Source Selection
Based on its source priority logic, MI 2200 can switch different sources
automatically to monitor 1. This monitor shall be used as driver's screen,
when installed in an according system constellation. In this case the
reversing camera has highest priority and will be shown automatically
when the rear gear gets active. Second priority has the navigation system
which is than usually displayed. Only when the car is parked and the navi-
gation system is switched into stand-by mode, one of the AV sources can
get activated. This function is for driver's safety reason.
Manual Source Selection
Monitor 2 - but also monitor 1 - when used in the constellation of a pure
rear seat entertainment system can display always one of the 2 possible to
connect AV sources
2
. In this configuration the desired source is selected via
the included IR remote control independently for each monitor.
Various Audio Output
MI 2200 offers audio output to each monitor. Further it includes a
2 channel RCA output to get sound through the car stereo system via it's
auxiliary input. To enable a wired headphone connection, one can utilize
RST 5400, VDO Dayton's elegant and easy to install connector terminal
3
. It
offers 3.5 mm output for both monitors sound as well as a 2 channel AV
input to allow i.e. the simple connection of a video camera or a game
console.
Input for up to 4 sources
The MI 2200 provides input for up to 4 different sources.
- 1 VDO Dayton Navigation System (PC 5xxx)
1
- 1 VDO Dayton Reversing Camera (RV 5100)
- 2 universal AV sources, such as DVD Player DV 6100 or
TV Tuner TV 5100
Integrated power supply for reversing camera
To make the installation more simple and less costly MI 2200 provides an
integrated power supply for a VDO Dayton Reversing Camera. This is the
most simple and safest way to get the rear view image on the screen.
IR Remote Control
The included credit card remote control RCM 5500 enables the indepen-
dent AV source selection for both monitors as well as the pre-adjustment
for each monitor's volume setting. Not selectable via the remote control is
the signal of the reversing camera and the navigation system
2
.
Status Indicator
This indicator lit up whenever a source is detected and the automatic
signal switching leads through such signal to the monitor.
VDO Dayton. The Car Brand.
Car Multimedia Systems.
www.vdodayton.com
Important notes
1)
In case a VDO Dayton Navigation System PC 5xxx is
connected, an additional monitor cable might be
required, which is not a part of MI 2200 packing
content. Please check out VDO Dayton's different
monitor cables to find the best matching one fitting
to your requirements.
2)
In case a VDO Dayton Navigation System PC 54xx or
higher is used in combination with a VDO Dayton
monitor MM 55xx or higher, the navigation signal
becomes also available.
3)
RST 5400 is an optional accessory. It offers also PS/2
input which can not be used with MI 2200.
Technical data
• Operating voltage: 10.5V - 15.6V, negative ground
• Power consumption: typical 2A / 3.2A (1/2 monitors)
• Operating temp. range: -20°C to +70°C
•Video in/out (AV1/2): 1Vpp / 75 Ohm
• Audio in (AV1/2): 2Vpp / 20 kOhm
• Audio 1 RCA out: 1.5Vpp / 10 kOhm
• Req. headphone impedance: min. 32 Ohm
(for use with RST 5400)
3
• Dimensions: 170 x 110 x 44 mm (wxdxh)
•Weight: ca. 350g.
Connections