Filter
Top Products
5
Many A/V processor feature delay seings. The purpose of delay is to enable surround and dialogue information to arrive at the listener’s ears at
the same time as the front channels, even when the listening seat is in a non-ideal position. On some processors, this can be achieved by seing
the distance from the listening position to each speaker, but other system allow only a time delay seing.
Rear Delay: If the listening position is equidistant from the front and rear speakers, set a low delay seing. The closer the listener is to the rear
speakers this higher the delay seing used should be.
Centre Delay: If the centre speaker is level with (or slightly behind) the front speakers, set the delay to zero. If the centre speaker is forward of
the front speakers, increase the delay.
LFE: In the cinema the low frequency eects channel is an extra bass channel with its own subwoofer. In domestic systems the LFE channel
typically feeds into the subwoofer. Where no subwoofer is used, the LFE signal is combined with the front channels and sent to the front
speakers. When you set the LFE level at your A/V processor, use care as powerful low frequencies can overload domestic loudspeakers. If you
hear popping or thumping noises coming from the front loudspeakers or subwoofer, immediately turn the A/V processor’s volume level down
and then lower the LFE level. This should cure the problem. If it does not, lower the volume level at the subwoofer (if you are using one) until
the problem disappears.
Phase: Please read the relevant sections of your A/V amplier manual and familiarise yourself with the various issues. If you are unsure, consult
your dealer for help. A home theatre system should have a precise front stage, a diuse rear stage and good localization of dialogue. If the
colours on the loudspeaker terminals do not correspond with those on the amplier, the sound will appear poorly focused or ‘out of phase’. For
this reason it is essential that the speakers are connected according to the wiring diagrams in this manual.
Connecting loudspeakers correctly (in phase) is essential whether the system is stereo or multichannel. This is especially important if you are bi-
wiring – if only one element in a bi-wired system is incorrectly connected (out of phase), the eects can be very noticeable yet hard to pinpoint.
Delay and LFE Settings
Setting Loudspeaker Sizes and Levels
If you are not using a subwoofer: Set the Front speakers to ‘Large’. Set the ‘Subwoofer’ option on the processor to ‘Off’ or ‘No’. The Front
channels will now receive all the system bass.
If you are using a subwoofer: When set to ‘Small’ all the system bass will go into the subwoofer. If you choose ‘Large’ the Front channel bass will
be reproduced from the Front speakers. Follow the instructions on this page for suitable size and crossover seings.
Once the loudspeaker seings have been nalised, put the A/V amplier into its ‘Test’ mode (see instructions supplied with your processor).
Adjust the level of each channel until all channels are reproduced at equal loudness.
On some programme material the surround channel may seem lower than the front. Do not readjust this level. You may, however, need to adjust
the subwoofer output level. Avoid seing too high a level or you will swamp the sound with bass. This can be tiring to listen to, and may limit
the subwoofer’s ability to respond to large bass transients. You should also set a sensible level going into the subwoofer from the A/V processor.
The subwoofer volume control should be between 12 o’clock and 3 o’clock.
Before investigating a problem, always switch o the system at mains.
If your system is not working properly please work through this checklist before returning the unit to your dealer.
Troubleshooting
Symptom Possible Cause
No Sound System not switched on; Speaker cables shorting terminals out; Wrong source selected
Sound lacks bass content Subwoofer not switched on
Lack of bass reproduction Subwoofer phase incorrect; Subwoofer crossover control too low
Excessive bass distortion at low volumes Subwoofer set to high; LFE level set too high; Subwoofer incorrectly wired
Excessive or distorted bass at high levels System level set too high; Bass control set too high; Subwoofer too close to room corners
Distorted / raling sound at high levels System level set too high; Objects too close to subwoofer
Popping or thumping from the subwoofer System level set too high; Subwoofer level set too high; LFE level set too high
Television picture colour is distorted
Subwoofer too close to TV. (Switch o system and TV, move units away, wait for 15 minutes,
switch on.)