JUMP-STARTING:
FOR OPTIMUM PERFORMANCE, WHEN USING YOUR POWER PACK UNIT TO JUMP START A VEHICLE OR BOAT, PLEASE READ AND
FOLLOW
THESE STEP-BY-STEP INSTRUCTIONS:
1. SWITCH THE ENGINE OF THE VEHICLE OR BOAT TO BE JUMP-STARTED TO “OFF”.
2. CONNECT THE RED (+) “ALLIGATOR” CLAMP TO THE RED (+) POSITIVE BATTERY TERMINAL.
3. CONNECT THE BLACK (-) “ALLIGATOR” CLAMP TO A NON-MOVING METAL PART OF THE ENGINE, NOT TO THE (-) NEGATIVE BATTERY
TERMINAL.
4. TURN POWER PACK UNIT SWITCH TO “ON”.
5. WAIT A MINUTE OR TWO TO LET THE VEHICLE BATTERY TO CHARGE
6. TRY TO START THE VEHICLE BUT DO NOT TRY FOR MORE THAN 5 TO 6 SECONDS.
7. IF THE VEHICLE OR BOAT ENGINE DOES NOT START, WAIT AT LEAST 3 MINUTES BEFORE TRYING AGAIN.
*UNDER NO CIRCUMSTANCES ALLOW THE RED AND BLACK CLAMPS TO TOUCH EACH OTHER OR A COMMON CONDUCTOR*
ONCE THE ENGINE IS RUNNING, FIRST DISCONNECT THE BLACK (-) CLAMP AND RETURN THIS CABLE TO ITS STORED POSITION ON THE
POWER PACK UNIT, THEN DISCONNECT THE RED (+) CLAMP AND RETURN THIS CABLE TO ITS STORED POSITION ON THE POWER PACK
UNIT. AS SOON AS POSSIBLE, CONNECT YOUR POWER PACK UNIT SYSTEM TO 120-VAC AND RECHARGE.
BATTERY REPLACEMENT
FIGURE 2. - REAR VIEW OF THE POWER PACK UNIT SHOWING THE BATTERY COMPARTMENT
1. UNSCREW AND REMOVE THE EIEVEN (11) PHILLIPS HEAD SCREWS THAT HOLD THE REAR COVER IN PLACE ON THE BACK OF YOUR
POWER PACK UNIT.
2. LIFT OFF THE COVER PLATE TO EXPOSE THE BATTERY COMPARTMENT.
3. LIFT THE BATTERY OUT OF THE BATTERY COMPARTMENT.
4. DETACH THE #4 JUMPER CABLES AND THE RED AND BLACK RECHARGING WIRES FROM THE BATTERY TERMINALS .
5. ENSURE THAT THE REPLACEMENT BATTERY IS ORIENTED WITH THE POSITIVE ON THE RIGHT SIDE AND THE NEGATIVE ON THE LEFT
SIDE, JUST AS THE OLD BATTERY CAME OUT.
6. CONNECT THE RED #4 JUMPER CABLE AND RED RECHARGING WIRE TO THE POSITIVE (+) BATTERY TERMINAL (ALSO MARKED WITH
RED),
THEN CONNECT THE BLACK #4 JUMPER CABLE AND RECHARGING WIRE TO THE NEGATIVE (-) BATTERY TERMINAL. DOUBLE CHECK ALL
CONNECTIONS, AND TIGHTEN.
7. SLIDE THE NEW BATTERY IN POSITION.
8. REPLACE THE BATTERY COMPARTMENT COVER AND SECURE IN PLACE WITH THE EIGHT (8) ''PHILLIPS'' (CROSS- HEAD) SCREWS.
SPECIFICATIONS
ITEM # . . . . . . . …. . . . . . . . . . . . . . . . . . . .ATD-5928
VOLTAGE . . . . . . . . . . . . . . . . . . . . . . . . . .12V DC
BOOST POWER . . . . . . . . . . . . . . . . . . . . .700 CRANKING AMPS
PEAK AMPS… …...…….. . . .. . . . . . . . . . .1700 AMPS
BATTERY TYPE . . . . . . . . . . . . . . . . . . . . .SEALED, LEAD- ACID, RECHARGEABLE, MAINTENANCE-FREE, 12V DC, 22-AMP-HOURS
BOOSTER CABLES . . . . . . . . . . . . . . . . . .74”, #4 AWG 100% COPPER CABLES WITH 1000 AMP "ALLIGATOR" CLAMPS
DIMENSIONS …. . . . . . . . . . . . . . . . . . .. . .40 x 37 x 13 CM
