Titan Tool 296235 Manual

Open as PDF

next previous

©TitanToolInc.Allrightsreserved. 3

Maintenance

Follow all safety precautions as described in the Safety

Precautions section of this manual before proceeding.

NOTE: Refer to the Parts List section in this manual for part

identication.

Replacing/Servicing the Seal Assembly

Ifyourspraygunleaksorspitsatthetipwhenyoureleasethetrigger,the

needleorseatisworn,damaged,ordirtyandmustbereplacedorcleaned.

Never attempt to perform maintenance on the spray gun

without first performing the “Pressure Relief Procedure.”

 1. Disconnecttheuidhosefromthegun.

 2. Removethetipandtipguard.

 3. Withthetriggerdepressed,removethediuserfromthefrontofthe

gun.

 4. Removethelocknut,rearhousing,andretractorpinsfromtherearof

the gun head.

 5. Removethesealassemblyfromthefrontofthegunheadbypushing

orgentlytappingatthebackofthesealassembly.

 6. Soaktheremovedpartsintheappropriatesolventandwipeclean.

 7. Inspectthepartsforwearordamageandusenewpartsduring

reassemblyofthegun,whennecessary.

NOTE: Lubricate all packings and moving parts before

reassembly with a lithium-based grease.

 8. Installthesealassemblyintothefrontofthegunhead.

9. Install the retractor pins into the rear of the gun head. Slide the rear

housing onto the retractor pins and secure in position with the lock

nut.

 10. WIththetriggerdepressed,installthediuserintothefrontofthe

gun head and tighten securely with a wrench.

 11. Performthe“AdjustingtheSealAssembly”proceduredescribed

below.

Adjusting the Seal Assembly

Proper adjustment of the seal assembly is essential to ensure

positive shut-off when the trigger is released.

 1. Tightenthelocknutuntiltherearhousingisushagainstthegun

head.

 2. Unscrewthelocknut3/4ofaturn.

NOTE: To check the adjustment of the seal assembly:

1. Move the gun trigger lock to the locked position.

2. Pull the trigger.

With the trigger lock engaged, there should be 1/32” of

movement between the lock nut and the rear housing

while pulling the trigger.

Replacing/Removing the Filter

 1. Pullthebottomofthetriggerguardforwardsothatitcomesloose

fromthehandleassembly.

 2. Loosenandremovethehandleassemblyfromthegunhead.

 3. Pulltheoldlteroutofthegunhead.

 4. Slidethenewlter,taperedendrst,intothegunhead.

 5. Makesurethehandlesealisinpositionandthreadthehandle

assemblyintothegunheaduntilsecure.

 6. Snapthetriggerguardbackontothehandleassembly.

Gun Filter Chart

Part

Number

Application Filter Type Color of

Filter Body

0089960 Syntheticresin,enamels,clean

varnishes,stains,azures

Extrane red

0089959 Basecoatenamels,primer

enamels,llers,markingpaints,

textured enamels

Fine yellow

0089958 Emulsions,latexpaints,acrylic

paints

Medium white

0089957 Fillerpaints,largeareasurfaces Coarse green

Parts List

Item Part # Description Quantity

 1 0296228 Gunhead ................................................................................1

 2 0296284 Triggerscrew,short ............................................................1

 3 0296285 Triggerassembly,4-ngergun ...................................... 1

 4 0296230 Triggerguard ........................................................................1

 5 0296270 Sealassembly ....................................................................... 1

 6 0296404 Diuser ...................................................................................1

 7 0297045 Seal ...........................................................................................1

 8 662-517 Tipassembly(includesitems7and10) ...................... 1

 9 0289228 Tipguard ...............................................................................1

 10 0297007 Tipseal .................................................................................... 1

 11 9910201 Locknut .................................................................................. 1

 12 0296222 Rearhousing .........................................................................1

 13 0296286 Retractorpin ......................................................................... 2

 14 0296287 Triggerscrew,long .............................................................1

 15 0089958 Filter,medium ...................................................................... 1

 16 0296289 Handleseal ............................................................................ 1

 17 0296342 Handle .....................................................................................1

 18 0296343 Spring ...................................................................................... 1

 19 0347706 Swivel ......................................................................................1

 20 0296291 Triggerassembly,2-ngergun ...................................... 1

 21 0279185 Collarassembly,2-ngergun .........................................1

  0296345 Handleassembly(includesitems17–19)

  0296294 Gunrepairkit(includesitems5,6,and11)