© Titan Tool Inc. All rights reserved. 33
Accessories and Service Kits
These items may be purchased separately from your local Titan
distributor.
Part # Description
103-830 5 Gal. Siphon Hose Assembly w/Rock Catcher
1” x 4.5’
103-808 55 Gal. Siphon Hose Assembly w/Rock Catcher
1” x 6.5’
103-627 Rock Catcher
930-004 Paint Filter Element, 0 Mesh (for mastics)
930-005 Paint Filter Element, 5 Mesh (for multicolors
and heavy materials)
930-006 Paint Filter Element, 50 Mesh (for latex and
normal architectural materials)
930-007 Paint Filter Elements, 100 Mesh (for stains,
lacquers and ne materials)
550-100 S-5 Gun w/Tip
550-110 S-5 Gun, Tip, and 1/4” Hose Kit
101-208 Grounding Clamp
101-212 Grounding Wire, 12 Gauge x 25’
314-480 Piston Lube, 8 oz.
314-482 Liquid Shield Plus, 1 quart
430-362 Coolo™ Hydraulic Fluid, 1 quart
430-361 Coolo™ Hydraulic Fluid, 1 gallon
975-212 2-Gun Manifold with Ball Valves, 1/4”
975-213 3-Gun Manifold with Ball Valves, 1/4”
975-312 2-Gun Manifold with Ball Valves, 3/8”
975-313 3-Gun Manifold with Ball Valves, 3/8”
808-550 3/8” NPS(M) x 3” hex tting
490-012 Hose coupling, 1/4” x 1/4”
730-397 High pressure uid gauge
314-171 Lubriplate, 14 ounce individual
314-172 Lubriplate, 6 lb. can
700-1037 Electrostatic discharge (ESD) wrist strap
Airless Tip Selection
Tips are selected by the orice size and fan width. The proper
selection is determined by the fan width required for a specic job
and by the orice size that will supply the desired amount of uid
and accomplish proper atomization.
For light viscosity uids, smaller orice tips generally are desired.
For heavier viscosity materials, larger orice tips are preferred.
Please refer to the chart below.
NOTE: Do not exceed the pump’s recommended tip size.
The following chart indicates the most common sizes and the
appropriate materials to be sprayed.
Tip Size Spray Material Filter Type
.011 – .013 Laquers and stains 100 mesh filter
.015 – .019 Oil and latex 50 mesh filter
.021 – .026 Heavy bodied latex and blockfillers 5 mesh filter
Fan widths measuring 8” to 12” (20 to 30 cm) are most preferred
because they offer more control while spraying and are less likely
to plug.
SAE O-Ring Fitting Installation
Steps 1 & 2:
Step 3:
Step 4:
Step 5:
Cautions:
Lubricate
Lubricate
Tighten nut
Recess
gap
No gap
Align
Hold
this part
stationay
Avoid screwing fitting in too far.
Avoid leaving fitting too far out.
Bent washer allows
for o-ring extrusion
O-ring cut on
thread
1. Pull washer and
o-ring back as far as
possible.
2. Lubricate o-ring and
entrance port.
3. Screw tting in until
washer pushes o-ring
into entrance and sits
at against port. (Do
not tighten! - only do
this step hand tight to
compress o-ring into
port!)
4. Back tting out
no more than one
complete turn to align
as required.
5. Torque nut wrench
tight holding backup
on tting. This should
expose a recess
gap behind the nut
which can act as an
indicator that the
tting is assembled
correctly. (This is a
feature for a specic
version of this tting
only - which screws
into the cylinder head.
Other ttings, as the
ones which attach to
the hydraulic pump,
assemble the same
but may not have the
indicator.)
