Titan Tool 800-1030 Manual

Open as PDF

next previous

Replacing the Filters

Pump Filter

1. Loosen and remove the lter housing by hand.

2. Slip the lter off of the lter support spring.

3. Inspect the lter. Based on inspection, clean or replace

the lter.

4. Inspect the o-ring. Based on inspection, clean or replace

the o-ring.

5. Slide the new or cleaned lter over the lter support spring

with the adapter in place. Push the lter into the center of

the pump block.

6. Slide the lter housing over the lter and thread it into the

pump block until secure.

NOTE: Thelterhousingshouldbehand-tightened,but

makesurethelterhousingisseatedfullyinto

the pump block.

Pump

Block

Filter

Spring

Filter Housing

Seal

Filter Support

Spring

Filter

Adapter

Gun Filter

1. Move the gun trigger lock to the unlocked position.

2. Loosen and remove the handle from the gun body.

3. Turning clockwise, unscrew the lter from the gun body.

NOTE: Left-handedthreadsrequireturningthelter

clockwise to remove.

4. Turning counterclockwise, screw the new or cleaned lter

into the gun body.

5. Make sure the handle seal is in position and thread the

handle into the gun body until secure.

6. Move the gun trigger lock to the locked position.

Handle

Seal

Filter

Gun

Body

NOTE: For more detail, part number information, and

complete assembly drawings, please see the LX-

Professional Airless Gun Owner’s Manual

(P/N 313-2293).

Replacing the Motor

Electrostatic discharge (ESD) potential could cause

damage to electronic control. Use Titan ESD wrist

strap P/N 700-1037 or equivalent when working on

electronic control with electronic cover removed.

1. Unplug the unit.

2. Loosen and remove the four motor shroud screws.

Remove the motor shroud.

3. Release the tie wrap on the side of the bafe assembly

and slip the bafe assembly off of the motor. Remove the

four bafe spacers.

4. Slide the electronic cover off of the electronic control

assembly on the motor.

5. At the electronic control assembly on the back off the

motor, disconnect the wire coming from the potentiometer

and the wire coming from the transducer. Also,

disconnect the two wires coming from the control panel

board (refer to the electrical schematic in the Parts List

section of this manual).

6. Remove the four control panel mounting screws. Pull

back the control panel for access to the control panel

board.

7. At the the control panel board, disconnect the two wires

coming from the motor (refer to the electrical schematic in

the Parts List section of this manual).

8. Loosen and remove the four motor mounting screws.

9. Pull the motor out of the gear box housing.

10. With the motor removed, inspect the gears in the gear

box housing for damage or excessive wear. Replace the

gears, if necessary.

Tie Wrap

Baffle Spacers

Baffle Assembly

Control Panel

Mounting

Screw

Gear Box Housing

Housing Gasket

Control

Panel

Motor Shroud Screw

Motor Shroud

Electronic Cover

Electronic Control

Assembly

Motor Mounting

Screw

10. Install the new motor into the gear box housing. Make

sure the housing gasket is positioned properly.

11. Secure the motor with the four motor mounting screws.

12. Reconnect the wires to the electronic control assembly

(refer to the electrical schematic in the Parts List section of

this manual).

13. Position the electronic cover over the electronic control

assembly.

14. Position the control panel on the gear box housing and

secure in position using the four control panel mounting

screws.

15. Slip the bafe assembly around the motor. Secure the

bafe assembly with the tie wrap. Slip the four bafe

spacers into position between the rear bell of the motor

and the bafe assembly.

16. Slide the motor shroud over the motor. Make sure the

housing gasket is positioned properly.

17. Secure the motor shroud with the four motor shroud

screws.