Filter
Top Products
128-6691
10 of 16
coco
coco
co TIME/FREQUENCY SELECTOR (T/F)
This unit can display the clock time, radio fre-
quency or CD player functions on the display
panel. Pressing the Time/Frequency Selec-
tor button when the radio frequency or CD
player track indication is shown, will change
the display to show the time. The time display
will automatically return to the radio frequency
or CD player function indication after 5 sec-
onds.
cpcp
cpcp
cp FM MONO/STEREO SELECTOR (MONO)
During FM radio operation, this button is used
to select mono or stereo reception of the broad-
cast signal. Under normal reception conditions,
the unit should be left in the stereo mode, as
indicated by
ST on the display panel when lis-
tening to an FM stereo signal. If the stereo sig-
nal is too weak for comfortable listening, press
the button to switch to mono reception (the
ST
indication will disappear and MONO appears
on the display panel). To return to the stereo
reception mode, press the button again so that
the
ST indication returns.
cqcq
cqcq
cq EQUALIZER SELECTOR (EQ)
The EQ button applies preset sound effects to
the unit’s audio output signal. The EQ button,
when pressed, will activate one of the following
operating modes: CLASSICS, POP M, ROCK M,
DSP OFF, or FLAT. When the EQ function is
active, as displayed (
EQ
----CLAS, POP, ROCK)
on the panel, the bass and treble levels can still
be changed to accommodate the listener’s ear.
However, when the levels are changed, the
equalizer function is disabled. When the EQ
function is not active, the unit returns to the user-
set bass and treble levels. The FLAT selection
indicates no equalizer enhancement of the pro-
gram, thereby removing the preset sound ef-
fects, unless otherwise desired. DSP OFF
disables display of the equalizer setting.
crcr
crcr
cr MODE SELECTOR (MODE)
This button is used to select the radio, or the
playback mode for the CD player. Each press
of the button will select a different mode
as indicated on the display panel.
During CD player operation, this button may
be used to change to radio without ejecting
the disc (the
CDP indication will remain on
the display panel to show that a disc is still
loaded in the unit). Press the button again to
return to CD player mode.
cscs
cscs
cs FRONT PANEL RELEASE BUTTON
This button is used to release the mecha-
nism that holds the front panel to the chassis.
To detach the front panel, press the button so
that the left side of the panel is released.
Grasp the released side and pull it off of the
chassis.
To re-attach the panel, position the right side
of the panel in place first and then press in the
left side of the panel until the mechanism
locks it into place.
ctct
ctct
ct THEFT-DETERRENT LED
The theft-deterrent Light Emitting Diode (LED)
is located behind the front panel and is ac-
cessible when the front panel is removed.
The flashing light serves as a visual warning
to the would-be thief that the unit has been
disabled by removal of the front panel.
cucu
cucu
cu RESET BUTTON
A RESET button is located on the front of the
chassis (front panel must be removed to
access the button). The RESET circuitry is
provided to protect the microprocessor cir-
cuitry and should only be activated under the
following circumstances as it will erase the
time and pre-set memories:
1. Upon initial installation after all wiring is
completed.
2.If there is a malfunction of any of the
switches on the unit, pressing the RESET
button may clear the system and return to
normal operation.
1010
1010
10
OPEROPER
OPEROPER
OPER
AA
AA
A
TT
TT
T
ING INSTRUCING INSTRUC
ING INSTRUCING INSTRUC
ING INSTRUC
TT
TT
T
IONSIONS
IONSIONS
IONS