Filter
Top Products
1010
1010
10
OPEROPER
OPEROPER
OPER
AA
AA
A
TT
TT
T
ING INSTRUCING INSTRUC
ING INSTRUCING INSTRUC
ING INSTRUC
TT
TT
T
IONSIONS
IONSIONS
IONS
dodo
dodo
do THEFT-DETERRENT LED
The theft-deterrent Light Emitting Diode (LED) is
located behind the front panel on the left side of the
chassis and is accessible when the front panel is
removed. The flashing light serves as a visual
warning to the would-be thief that the unit has been
disabled by removal of the front panel.
dpdp
dpdp
dp
RESET BUTTON
A RESET button is located on the front of the chassis
above the theft-deterrent LED (front panel must be in
the fold-down position to access the button). The
Reset circuitry is provided to protect the micropro-
cessor circuitry and should only be activated under
the following circumstances, as it will erase the time
and tuner pre-set memories:
1. Upon initial installation after all wiring is com-
pleted.
2. If there is a malfunction of any of the switches
on the unit, pressing the RESET button may
clear the system and return to normal opera-
tion.
NOTES ON USE OF FRONT PANEL
1. Make sure the front panel is right-side-up when
attaching it to the chassis as it cannot be at
tached when up-side down.
2. Do not press very hard on the front panel when
attaching it to the chassis. No morethan light to
moderate pressure should be needed.
3. Whenattaching the front panel, make sure the
right side is correctly engaged before pressing
the left side to lock it into position.
4. When taking the front panel with you, please
use the supplied carrying case to protect the
panel from dirt and damage. Make sure there
is no dust or dirt on the electrical terminals on
the back of the panel as this could cause
intermittent operation or other malfunctions.
ctct
ctct
ct TIME/FREQUENCY SELECTOR (DISP)
This unit can display either the clock time or radio
frequency/CD player functions. Ordinarily, the
radio frequency or CD player track indication is
displayed, but the display can also show the
time when this button is pressed. The time will
then be displayed for approximately 5 seconds,
after which it will return to the radio or CD player
function display.
The correct time-of-day can also be set into the
unit by pressing the DISP button. This procedure
is outlined later in these operating instructions.
cu cu
cu cu
cu CD PLAY/PAUSE (PAUSE) BUTTON
This button is used to pause disc play when
desired. During CD player or optional changer
operation, this button may be used to pause disc
play without ejecting the disc in the player
(the indication will remain on the display
panel to show that a disc is still loaded in the
unit). Press the button again to resume disc play
from the point at which it was stopped.
dldl
dldl
dl
FRONT PANEL FOLD-DOWN BUTTON
This button is used to release the mechanism that
holds the front panel to the chassis. To detach the
front panel, press the button so that the panel
folds down to the lowered position. This position
permits access to the CD slot and the CD Eject
( ) button.
dmdm
dmdm
dm FRONT PANEL REMOVAL ( ) BUTTON
This button is used to release the mechanism that
holds the front panel to the panel mounting plate. To
detach the front panel, press the button so that the
left side of the panel is released. Grasp the re-
leased side and pull it off of the chassis. To re-
attach the
panel, position the right side of the panel in place
first and then press the left side of the panel until
the mechanism locks it into place.
dndn
dndn
dn REMOTE SENSOR
The sensor to detect the infrared signal from the
wireless remote control is located behind the VFD
display lens. For optimum operation of the remote
control, always aim the control at the VFD display.
CD
DETACHING THE
FRONT PANEL
RELEASE
BUTTON
ATTACHING THE FRONT PANEL
ENGAGE RIGHT SIDE FIRST