Filter
Top Products
E-3
General Operations
Volume Level Control and Memory
Rotate the dial to set the memory for the volume level which
will be recalled when the unit is turned on.
1. Adjust the volume level. Spinning or fast rotation of the
dial knob will increase the number of turns needed to
reach max. volume.
2. Hold the
PWR
pressed for more than 2 seconds.
The unit will turn off and the selected max. turn-on
volume level is set in memory.
Note
If the unit is turned off with the volume lower than the memory
setting, the unit will return to the lower setting when turned
back on.
Muting the sound
Press
MUTE / SENS
.
“ MUTE ” apeares on the display window.
To restore the previous volume level, press
MUTE / SENS
again.
Setting the Clock
1. Turn the ignition key to the ON position.
2. Press the
PWR
to turn on the unit.
3. Press the
DISP
to display “ CLK ADJ ”.
A. Press the
MUTE / SENS
within 3 seconds to flash the “ 12 ”
(HOUR ADJ).
B. Rotate the dial to set the hour digit.
C. Press the
MUTE / SENS
to flash the “ 00 ” (MIN ADJ).
D. Rotate the dial to set the minute digit.
Volume down
Volume up
4. Press the
DISP
to display “ CLOCK 12 ”.
5. Rotate the dial to select the 12 or 24-hour time mode.
Each time you rotate the dial, the mode changes or
toggles as follows;
CLOCK 12
ÔÔ
ÔÔ
Ô CLOCK 24
6. Press the
DISP
momentarily. The clock is activated.
Ignition-off Clock Recall
The display will illuminate showing the time and then auto-
matically shut off after 5 seconds.
Press the
DISP
while the ignition switch is in the “ OFF ” posi-
tion.
Mode Selector
Each time the
DISP
is pressed, the display window will change
over as shown below;
Priority ➜ STN CALL ➜ LEVEL 1 ➜ Temporary ( NO NAME )
CLOCK 12 CLK ADJ METER 1
Display priority setting
Display Priority can be set for the following items;
Radio mode
• Frequency and Station Name, plus during
CDC(CD changer) mode (HOUSTON DM189 only)
• Track No, Track time and Disc name.
Example
To set Station Name to the Display Priority.
1. Press the
DISP
three times, and the temporary display
appears in the display window.
2. Hold the
DISP
pressed for more than 2 seconds.
“ NO NAME” or any station name blinks once to indicate
that Station Name is selected for the Display Priority.
After 5 seconds, the display mode will automatically re-
turn to the Display Priority showing either “NO NAME” or
the station name.
Tip
Frequency Display is initially set as the Display Priority,
and Station Name (“NO NAME”) is set to “Temporary”.
Adjusting the Sound Characteristics
1. Press the
AUD
to select the desired adjustment mode.
BASS 0 ➜ TREBLE 0 ➜ LOUD OFF(LOUDNESS)
R0 F0(FADER) L0 R0(BALANCE)
2. Rotate the dial to adjust the selected item.
Adjust within 3 seconds after selecting the item.
After 3 seconds, the dial functions as volume control.
Use the following tables as a guide for adjusting the set-
tings in each mode.
BASS BASS -5 BASS +5
TREBLE TREBLE -5 TREBLE +5
LOUD LOUD OFF LOUD ON
BALANCE L9 R0(Full left) L0 R9(Full right)
FADER R9 F0(Full rear) R0 F9(Full front)
➜
➜
➜
➜
➜
➜
➜
HOUSTON (En)_P1-11 3/23/99, 3:05 PM3