Filter
Top Products
Basic Operations
English
15 DXZ385USB
● Adjusting the treble
This adjustment can be performed only when
the Z-Enhancer Plus is set to “CUSTOM ”.
2-1. Select “TREBLE”.
3-1. Press the [w] or [z] button to select as
following order.
“TREB<G>” ↔ “TREB<F>”
∗ The factory default setting is “TREB<G>”.
3-2. Press the [ ] button.
3-3. Press the [w] or [z] button to adjust the
gain, the F (center frequency) and the Q.
TREB<G>:The factory default setting is “0”.
(Adjustment range: +7 to
–7)
TREB<F>: The factory default setting is
“10k”.
(Adjustment range:
10k/12.5k/15k/17.5k)
3-4. Press the [ ] button to return to the
previous mode.
● Adjusting the balance
2-1. Select “BALANCE”.
3-1. Press the [w] or [z] button to adjust the
balance of the right and left speakers.
∗ The factory default setting is “CENTER”
(center). (Adjustment range: RIGHT12 to
LEFT12 (right 12 to left 12))
● Adjusting the fader
2-1. Select “FADER”.
3-1. Press the [w] or [z] button to adjust the
balance of the rear and front speakers.
∗ The factory default setting is “CENTER”
(center). (Adjustment range: FRONT12 to
REAR12 (front 12 to rear 12))
● Setting the subwoofer
You can set the low pass filter of subwoofer.
2-1. Select “S-W LPF”.
3-1. Each time press the [w] or [z] button to
select the setting, the setting changes in
the following order:
“THROUGH” ↔ “LPF 50” ↔ “LPF 80” ↔
“LPF 120”
∗ The factory default setting is “THROUGH”.
● Adjusting the subwoofer output
volume
You can adjust the volume output from the unit’s
subwoofer output terminal.
This adjustment can be performed only when
the “S-W LPF” is set to “LPF 120”, “LPF 80” or
“LPF 50”.
2-1. Select “S-W VOL”.
3-1. Press the [w] or [z] button to increases
or decreases the subwoofer volume.
∗ The factory default setting is “0”.
(Adjustment range: +6 to –6)
∗ When the volume level is more than 30, the
subwoofer volume adjustment value can not
reach +6.
● Adjusting the high pass filter
2-1. Select “HPF”.
3-1. Each time you press the [w] or [z] button
to select the setting.
The setting changes in the following order:
“120” ↔ “THROUGH”
∗ The factory default setting is “THROUGH”
(through).
∗ This is supported only with amplifiers
equipped with this function. Output is not
supported from RCA cables.
Note:
• During SOUND adjustment mode, if no operation
is performed for more than 10 seconds, this
mode can be cancelled and return to previous
mode.
Setting the MAGNA BASS EXTEND
The MAGNA BASS EXTEND does not adjust
the low frequencies like the normal sound
adjustment function, but emphasizes the deep
bass frequencies to provide you with a dynamic
sound.
∗ The factory default setting is “OFF” (off).
1. Press and hold the [SOUND] button for 1
second or longer to turn on the MAGNA
BASS EXTEND effect. “M-B EX” appears in
the display for 2 seconds.
2. Press and hold the [SOUND] button for 1
second or longer to turn off the MAGNA
BASS EXTEND effect.