Jensen JCD3006 Car Stereo System User Manual


 
JCD3006
6
BASIC OPERATION
Control Panel Release (REL)
Press the REL button (3) to release the control panel.
Power On/Off ( )
Press the button (1) to turn the unit ON or OFF.
Volume Control
To increase the volume, rotate the volume control
knob (6) clockwise.
To decrease the volume, rotate the volume control
knob counter clockwise.
When the volume is adjusted, the volume level is
shown on the display panel as a number ranging from
00 (lowest) to 100 (highest).
Mute
Press the MUTE button (8) on the control panel (or the
MUT button on the remote control) to mute the audio
output. “Mute” will appear on the display. Press MUTE
again to restore the audio output to the previous level.
Mode
Press the MODE button (5) on the control panel (or
the MOD button on the remote control) to select a
different mode of operation, as indicated on the
display panel. Available modes include Radio, CD, and AUX In (optional Auxiliary Input).
Auxiliary Input
1. Connect the external signal to the “Aux In” jack (22) located on the front of the control
panel.
2. Press the MODE button to select Aux In mode.
3. Press MODE again to cancel Aux In mode and return to previous mode.
Display (D)
Press the D button (18) on the control panel (or the DISP button on the remote control) to view
the clock. The LCD will display the clock for 5 seconds, then return to the previous display
mode.
Clock Adjustment
With the clock displayed, press the D button (18) until the LCD flashes. Press the up >>| (21)
button to adjust the hours or the down |<< button (20) to adjust the minutes. (You can also use
the U and D buttons on the remote control to set the hour and minutes.)
Reset
After releasing the control panel, use a pencil or any non-metallic
object to press and hold the RESET button for five seconds to reset
the main unit. The unit will return to the factory default settings. The
reset button should be activated for the following reasons:
initial installation of the unit when all wiring is completed
function buttons do not operate
error symbol on the display
NOTE: If after pressing the RESET button the unit still does not function normally, use a
cotton swab soaked in isopropyl alcohol to clean the socket on the back of the control
panel.
Audio Menu
Press the volume control button (4) on the control panel (or the S button on the remote control)
to access the Audio Menu. You can navigate through the Audio Menu items by pressing the
volume control button repeatedly, or by pressing the up >>| (21) or down |<< (20) buttons.
Once the desired menu item appears on the display, adjust that option by turning the volume
control knob within 5 seconds. The unit will automatically exit the Audio Menu after five
seconds of inactivity. The following menu items can be adjusted.
Volume Level
Use the volume control knob to adjust the Volume level from “00” (lowest) to “100” (highest).
Bass Level
Use the volume control knob to adjust the Bass level range from “-10” to “+10”.
Treble Level
Use the volume control knob to adjust the Treble level range from “-10” to “+10”.
Balance
Use the volume control knob to adjust the Balance between the right and left speakers from
“R10” (full right) to “L10” (full left). “C00” represents an equal balance betw
een the right and left
speakers.
Fader
Use the volume control knob to adjust the Fader between the front and rear speakers from
“R10” (full rear) to “F10” (full front). “C00” represents an equal balance between
the front and
rear speakers.
JCD3006
1
2
3
5
6
7
89
10
11
20
21 12
13
14
15 16
17
18
19
4 22
4
1
21
20
5
19
11
8
9
6
18
7
10
14
13
17
15
12
16
23
VOL
SHUF
BND
TR. DN
LOC
MUT
1
PAU
MO
4
SCN
2
5
SCN
AMS
LOUD
D
VOL
RPT
3
DISP
6
MOD
TR. UP
PEQ
U
S
RESET