Filter
Top Products
VM9510TS
1
PREPARATION
Congratulations on your purchase of the Jensen VM9510TS
Mobile Multimedia AM/FM/DVD Receiver.
It’s a good idea to read all of the instructions before beginning
the installation. We recommend having your Jensen
VM9510TS installed by a reputable installation shop.
Features
• Single DIN Size
• Ultra slim slot-in DVD core mechanism
• 7 inch Panasonic TFT monitor
• Wide screen TFT display and segment LCD display
• Rotary volume control
• ISO Double-DIN chassis
• Light weight proprietary DVD core mechanism
• Wide screen (16:9) 6.5" TFT touch screen monitor
• Main System 18 Watts x 4 RMS / 60 Watts x 4 Peak
• 240 watts total system power
• Multi-Zone media distribution
• AM / FM Tuner
• TV Tuner with antenna
• Supports NTSC and PAL, auto negotiation
• Full, Wide, Normal and Off (Standby) screen modes
• Motorized TFT panel has 16 precise angle adjustments
via remote control or infinitely variable manual
adjustment from the front panel
• Auto-activated rear view camera input - Reverse gear
over rides the TFT screen to display video from a rear
mounted camera
• Over current motor protection for obstructed TFT panel
• Compatible optical / SD Card formats: DVD-R/RW,
DVD+R/RW, CD-R/RW, CD-DA, MP3, WMA, HDCD,
SVCD, VCD, MPEG (MPEG 1), MPEG 4, JPEG, MP3/
WMA files burned onto a DVD+R/RW or DVD-R/RW
and Kodak Picture CD
• SD Card slot
• Multi-language, multi-subtitle and multi-angle playback
options
• Last position memory for optical disc.
• Parental Lock - Uses a password and disc rating set-up
to prevent unauthorized user access from display
content
• Audio Mute
• 5-Way joystick navigation
• Two remote controls - a full function front remote control
and a limited function Kid-Zone remote control for back
seat operation
• Over and under voltage protection to insure the unit
operates within designed parameters
• Damped DVD mechanism with 16Mbit flash memory
ESP (Electronic Shock Protection) provide smooth disc
playback under the severest road conditions
Tools and Supplies
You will need these tools and supplies to install your
VM9510TS:
• Torx type, flat-head and Philips screwdrivers
• Wire cutters and strippers
• Tools to remove existing radio (screwdriver, socket
wrench set or other tools)
• Electrical tape
• Crimping tool
• Volt meter/test light
• Crimp connections
• 18 gauge wire for power connections
• 16 – 18 gauge speaker wire
WARNING! Only connect the unit to a12-volt power
supply with proper grounding.
WARNING! Never install this unit where operation and
viewing could interfere with safe driving conditions.
WARNING! To reduce the risk of a traffic accident (except
when using for rear view video camera) never use the
video display function while driving the vehicle. This is a
violation of federal law.
WARNING! Never disassemble or adjust the unit without
the assistance of a professional. For details, please
consult your local car stereo specialty shop.
WARNING! To prevent injury from shock or fire, never
expose this unit to moisture or water.
WARNING! Never use irregular discs.
WARNING! To prevent damage to the mechanism inside
this unit, avoid impact to the TFT monitor.
WARNING! Do not change the fuse on the power wire
without professional guidance. Using an improper fuse
may cause damage to the unit and result in a fire.
WARNING! The monitor employs an automatic motorized
mechanism. To prevent damage to the core mechanism,
please do not push, pull or swivel the monitor manually.
Disconnecting the Battery
To prevent a short circuit, be sure to turn off the ignition and
remove the negative (-) battery cable prior to installation.
NOTE: If the VM9510TS is to be installed in a car
equipped with an on-board drive or navigation computer,
do not disconnect the battery cable. If the cable is
disconnected, the computer memory may be lost. Under
these conditions, use extra caution during installation to
avoid causing a short circuit.