Filter
Top Products
2
A
B
C
To prevent short circuits, we recommend that you disconnect the battery’s negative terminal and make all electrical connections before installing the receiver.
• Be sure to ground this receiver to the car’s chassis again after installation.
Notes:
• Replace the fuse with one of the specified rating. If the fuse blows frequently, consult your JVC car audio dealer.
• It is recommended to connect to the speakers with maximum power of more than 50 W (both at the rear and at the front, with an impedance of 4 Ω to 8 Ω).
If the maximum power is less than 50 W, change “AMP GAIN” setting to prevent the speakers from being damaged (see page 21 of the INSTRUCTIONS).
• To prevent short-circuit, cover the terminals of the UNUSED leads with insulating tape.
• The heat sink becomes very hot after use. Be careful not to touch it when removing this receiver.
ELECTRICAL CONNECTIONS
Heat sink
Typical Connections
Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this receiver.
The leads of the power cord and those of the connector from the car body may be different in color.
1 Connect the colored leads of the power cord in the order specified in the illustration below.
2 Connect the antenna cord.
3 Finally connect the wiring harness to the receiver.
*
2
Before checking the operation of this
receiver prior to installation, this lead must
be connected, otherwise power cannot be
turned on.
Line out (see diagram )
Rear ground
terminal
15 A fuse
Black
Blue with white stripe
Red
Yellow
*
2
*
1
Not included for this receiver
To metallic body or chassis of the car
Ignition switch
Fuse block
To an accessory terminal in the fuse block
To the remote lead of other equipment (200 mA max.)
Left speaker (front)
Right speaker (front) Left speaker (rear) Right speaker (rear)
PurplePurple with black stripeGreenGreen with black stripeGrayGray with black stripeWhiteWhite with black stripe
To a live terminal in the fuse block connecting to the car battery
(bypassing the ignition switch) (constant 12 V)
SUBWOOFER
*
3
Blue
To CD changer or another external component (see diagram )
Antenna terminal
*
3
Only for KD-G614 (see diagram )
To the automatic antenna if any
(250 mA max.)
Orange with white stripe
Brown
To car light control switch
To cellular phone system—only for KD-G614
Connecting the external amplifiers
You can connect amplifiers to upgrade your car stereo system.
• Connect the remote lead (blue with white stripe) to the remote lead of the other equipment so that it can be controlled through this receiver.
•
Disconnect the speakers from this receiver, connect them to the amplifier. Leave the speaker leads of this receiver unused.
*
4
Firmly attach the ground wire to the
metallic body or to the chassis of the
car—to the place not coated with paint
(if coated with paint, remove the paint
before attaching the wire). Failure to do
so may cause damage to the receiver.
Front speakers
Rear speakers
JVC Amplifier
Remote lead
Y-connector (not supplied for this receiver)
Remote lead (Blue with white stripe)
To the remote lead of other equipment or auto antenna if any
Front speakers
Subwoofer
JVC Amplifier
Only for KD-G614
Only for KD-G614
JVC Amplifier
*
5
Signal cord (not supplied for this receiver)
CD changer
Connecting the external components
CAUTION:
• Before connecting the CD
changer, make sure that the
receiver is turned off.
*
6
Connecting cord supplied for
your CD changer
• Refer also to page 13 of the INSTRUCTIONS.
JVC CD changer
*
7
Only for KD-G614
External component
*
8
Line Input Adapter KS-U57
(not supplied for this receiver)
External component
• Set “EXT IN” to “EXT IN” (See page 21 of the INSTRUCTIONS.)
KS-U57*
8
CD changer jack
Instal1-2_G614_G514_002A_f.indd 3Instal1-2_G614_G514_002A_f.indd 3 12/22/04 11:27:49 PM12/22/04 11:27:49 PM