Filter
Top Products
46
|
KDC-BT60U/ KDC-6047U
Bluetooth Setup
Bluetooth Setting
You can select following Bluetooth Setting items.
1
Enter Bluetooth mode
KDC-BT60U
Press the [ ] button.
KDC-6047U
Press the [TI] button for at least 1 second.
✍ You can also select from “Settings” in Menu List
mode.
2
Turn the [VOL] knob and press it when the
desired item is displayed.
Select “BT Settings”.
3
Select the Menu item
Turn the [VOL] knob and press it when the
desired item is displayed.
Display Overview
“BT Settings”
“Phone Selection” Select a cell-phone or Bluetooth audio player
connection.
Refer to <Selecting the Bluetooth device You
Wish to Connect> (page 48).
“Audio Selection”
“SMS Download” Download a short message.
Refer to <Downloading the SMS> (page 52).
“SMS inbox” Display the received short message.
Refer to <SMS (Short Message Service)>
(page 52).
“Voice Tag” Registers voice for voice recognition and voice
to select the Phone number category in Phone
book.
- Adding a Voice Dialing Command (page 50)
- Setting a Voice Command for Category (page
50)
“Detailed Setup” Move to detailed item.
“Device Regist.” Register a Bluetooth device (pairing).
Refer to <Registering Bluetooth device>
(page 47).
“SPCL DVC
Select”
“Device Delete” Cancel registration of the Bluetooth device.
Refer to <Deleting a Registered Bluetooth
device> (page 49).
“PIN Code Edit” Specify the PIN code required when registering
this unit using the Bluetooth device.
Refer to <Registering PIN Code> (page 48).
“Auto Answer” Answer a call automatically after lapse of the
preset time interval for automatic answer.
“OFF”/ “0s” – “8s” – “99s”
“Bluetooth HF/
Audio”
You can specify output speakers for hands-free
voice communication and Bluetooth audio
sound.
“FRONT”: Outputs voice from the front
speakers.
“ALL”: Outputs voice from the front and rear
speakers.
“Call Beep”
You can output a beep from the speaker when
a call comes in.
“ON”: Beep is heard.
“OFF”: Beep is canceled.
“BT F/W Update” Display the version of the firmware of this unit.
“Mic Gain”
Adjust the sensitivity of the built-in microphone
for a telephone call. Adjust the voice of caller.
Setting to “+” increases the voice volume.
“–3” – “0” – “+3”
“NR Level”
Reduce the noises generated by surrounding
environment without changing the built-in
microphone volume. Adjust the voice of caller
when it is not clear. Setting to “+” increases the
noise reduction.
“–3” – “0” – “+3”
“Echo Cancel LV“
Adjust the level of echo cancellation. Setting to
“+” increases the echo cancel reduction.
“–2” – “0” – “+2”
( : Factory setting)
4
Make a setting
• When the “
PUSH
” icon is displayed (at the
right edge of the display)
Turn the [VOL] knob to select a setting value,
and then press the [VOL] knob.
• When the “
PUSH
” icon is not displayed
Press the [4] or [¢] button to select a
setting value.
5
Exit BT Settings mode
KDC-BT60U
Press the [ ] button.
KDC-6047U
Press the [TI] button for at least 1 second.
Remarks
• “Auto Answer” (Setting the Time Interval for Automatic
Answer)
This function automatically answers (responds to) a call
after lapse of the preset time interval for automatic answer.
“OFF” : Does not answer the phone call automatically.
“0” : Automatically answers the phone call at once.
“1s” – “99s” : Automatically answers the phone call after
lapse of 1 – 99 seconds.
⁄
• If the time set in the cell-phone is shorter than that set in
Function of KDC-BT60U
KDC-6047U with KCA-BT200 (Optional Accessory)
4
MENU VOL
¢38
/ TI