LG Electronics 32LY560M Car Satellite TV System User Manual


 
30
206-4261
117 - FACT DEFAULT (Factory Default)
Set to 1 and press OK to restore the factory default settings of all
Installer Menu items. Once complete, the value returns to 0.
Caution: If set to 1, this clears all Installer Menu custom
settings and restores the factory default settings. It also
clears the channel lineup, including any assigned
channel icons and custom text labels.
Note: See also Reference section, “Restoring Factory Defaults on
the TV(s),” for further information.
119 - DATA CHANNEL
Set to 0 to disable. Set from 1 to 135 to match the RF channel
number that will be used by the Pro:Centric server as its data
channel. If left at the default value (255), the TV’s Data Channel
Auto Search feature will be enabled (see additional information
below). *
Data Channel Auto Search feature: When this item is set to 255
(default), once every 24 hours, the TV will initiate a search of 10
predened channels (10, 20, 30, ... 100) and then, if necessary,
perform a complete search of the RF channels (1 to 135) in an
attempt to nd the RF channel used by the Pro:Centric server as
its data channel. If the Pro:Centric RF channel is found, the DATA
CHANNEL value will be changed from 255 to match the server’s
RF channel number. The time at which the Auto Search occurs
depends on the setting of item 121 UPDATE TIME HR. See item
121 description for further information.
Note: Pro:Centric updates are downloaded from the Pro:Centric
server to the TV when the TV is turned OFF. While Pro:Centric
updates are in progress, it is not possible to turn ON the TV.
Note: The Data Channel is automatically set to “253” if Media
Type is set to “IP” either in the Express Script Installer Menu
Wizard or in the IP Environment / Pro:Centric Menu on the TV
(see “Express Script Installer Menu Wizard” on pages 12 to 17 or
“Pro:Centric Setup” on pages 59 to 60, respectively) or if Installer
Menu item #119 Data Channel is set to “IP Address” in the FTG
File Manager, which is used to congure TV CPUs for FTG Mode
operation. It is not possible to change the value to “253” directly in
the Installer Menu.
121 - UPDATE TIME HR
Based on the settings of this item and item 122 UPDATE TIME MN,
the Wake For Update feature wakes the TV once daily to check for
and, if applicable, download updates from the Pro:Centric server.
Set the Wake For Update hour from 0 to 23. This item uses the
24-hour clock format. The value “128” (default) is displayed as
“OFF.” Directly entering 128 resets the default value (OFF) for this
item, though note that this setting does not mean the TV will not
initate update events—see additional information below.
If Wake For Update is OFF, the time at which a Data Channel
Auto Search (item 119 set to 255) occurs is determined as follows:
The TV will initiate the search at 2:00 PM (if the TV clock is set) or
after 14 hours of elapsed time from when AC power was applied
(if the TV clock is not set).
If the TV display is ON when the Auto Search is due to occur, the
Auto Search will take place the next time the TV is turned OFF.
Note: This item is not available in the Installer Menu when item
119 DATA CHANNEL is set to 0.
Note: The TV clock must be set in order for a Wake For Update
event to occur at the precise time of day in accordance with item
121 and item 122 settings.
122 - UPDATE TIME MN
Set the Wake For Update minute from 0 to 59. See also description
for item 121 UPDATE TIME HR above.
Note: This item is not available in the Installer Menu unless item
121 UPDATE TIME HR HR is set from 0 to 23.
Note: The TV clock must be set in order for a Wake For Update
event to occur at the precise time of day in accordance with item
121 and item 122 settings.
Installer Menu (Cont.)
* PCS150R and later Pro:Centric servers do not support HRC or IRC cable channel frequencies.