Marshall electronic V-R231P-AFHD Car Video System User Manual


  Open as PDF
of 4
 
Power In
4 Pin Male XLR
Pin-1 GND
Pin-2 +24v
Active Outputs require power to be applied
All input signals appear as output signal
Analog output signals are buffered and amplifi ed
Pin1-Yel
Pin2-Red
Pin3-Grn
Pin4-
Pin5-Gnd
Pin6-
Pin7-
Pin8-
Pin9-
Pin10-
Pin11-
Pin12-
Pin13-
Pin14-
Pin15-Gnd
Tally IN
DB-15 Female
VESA 75mm
mount points
S-Video In
4 Pin Din (Female)
Pin1 - GND
Pin2 - GND
Pin3 - Yin
Pin4 - Cin
S-Video Out
4 Pin Din (Female)
Pin1 - GND
Pin2 - GND
Pin3 - Yout
Pin4 - Cout
Marshall Electronics
3
5
Operational Setup
1. Unpack the V-R231P-AFHD and accompanying V-PS24-7.5 power supply. Physically inspect for any damage that may have occurred
during shipping. Should there be any damage, immediately contact Marshall Electronics at 800-800-6608. If you are not located within the
continental united states call +1 310-333-0606.
2. After inspection, install in your desired location. Marshall Electronics offers a desk top stand or rack mount kit for a standard EIA 19-inch
equipment rack. Adequate ventilation is required when installed to prevent possible damage to the V-R231P-AFHD internal components.
3. Connect required cables for signal input and output. Please note that power must be applied to the V-R231P-AFHD for all outputs to be
activated. All BNC connectors should be rated for 75Ω.
4. Attach XLR 4 pin power connection from V-PS24-7.5 power supply to the back of the unit.
5. Plug the V-PS24-7.5 power supply into the A.C. source
6.Turn on the V-R231P-AFHD by depressing the power switch located on the front of the unit.
6
Connectors
* HDSDI/SDI Inputs comply to SMPTE-259M, 292M, SDI-270Mbs, HDSDI-1.42 Gbs
* Component Inputs comply to SMPTE274M, 294M,295M,296M
* Composite Video Inputs comply to SMPTE-170M
* Tally lamps active when connected to ground
Input Signal Type and aspect
DVI-D DVI-A
4x3 16x9 4x3 16x9
800 x 600 60Hz YYYY
1024 x 768 60Hz YYYY
Table 1 Computer Signals Displayed via DVI-I connector
(VGA to DVI adapter may be required)
Table 2 Video Signals Displayed via DVI-I and YPrPb connections
(HDMI requires adapter to DVI)
Input Signal Type and aspect YPbPr DVI-D
720 x 486 60i Y N
720 x 576 50i Y N
720 x 486 60P Y Y
720 x 576 50P Y Y
1280 x 720 60P Y Y
1280 x 720 50P Y Y
1280 x 720 30P Y N
1280 x720 29.97P Y N
Input Signal Type and aspect YPbPr DVI-D
1280 x720 25P Y N
1280 x 720 24P N N
1280 x 720 23.98P N N
1920 x 1080 60i Y Y
1920x1080 59.94i Y Y
1920 x 1080 50i Y Y
1920 x 1080 30P Y Y
1920x1080 29.97P Y Y
 previous