Filter
Top Products
10
En
PARTS AND THEIR FUNCTIONS
PARTS AND THEIR FUNCTIONS
FRONT PANEL
This section explains the use of the unit when controlling DJS. Depending on the DJ software program used, some functions may not be
supported or may require different operations than those described in this manual.
1EJECT (
) button
Not used during DJS control.
2 Loop control buttons
Loop-in button (IN/CUE)
Use to set loop-in points. When this button is pressed during
loop playback, playback returns to the loop-in point and
recommences.
Loop-out button (OUT/ADJUST)
Use to set loop-out points. If this button is pressed during loop
playback, the jog dial or SEARCH buttons can be used to adjust
the position of the out point.
RELOOP/EXIT button
Press this button during loop playback to cancel loop play.
When the unit is not in loop play mode, pressing the button will
cause loop play to begin from the previously set loop-in point.
3 TEMPO control section
TEMPO control range button (±6/10/16/WIDE):
Each time the button is pressed, the variable range of the
TEMPO adjust slider changes.
MASTER TEMPO button and indicator (MT):
Each time the button is pressed, the master tempo function
alternates ON/OFF.
TEMPO adjust slider:
From the center detent position, pull the slider towards you (+)
to increase the tempo, and push the slider away from you (–)
to slow down the tempo.
PITCH BEND +/– buttons:
When pressed during play, the pitch bend function is enabled.
Pressing the “+” button accelerates the pitch bend speed, and
pressing the “–” button decelerates the pitch bend speed.
The speed of the pitch change can be modified by holding the
button depressed while rotating the jog dial.
4 TRACK SEARCH (
,
) buttons
Use to perform track search.
5SEARCH (
,
) buttons
Use to perform fast forward and reverse.
6 CUE button and indicator
Use to set cue points. Also when a cue point has been set,
pressing the CUE button sets the unit to the cue standby mode.
7 Play/pause (
) button and indicator
Use to start and pause playback.
8 Time mode/auto cue button (TIME/A.CUE)
TIME:
Each time the button is pressed, the display’s time display
alternates between the current track’s elapsed playing time,
and the remaining time (REMAIN).
A.CUE:
When held depressed for one second or more, the AUTO CUE
function alternates ON/OFF.
9 SCRATCH button
Press to set the scratch mode ON/OFF.
10 JOG BREAK button
Not used during DJS control.
11 BROWSE button
Use to switch to the BROWSE screen.
12 MIX button
Use to switch to the MIX screen.
13 EFFECT button
Use to switch to the EFFECT screen.
14 UTILITY button
Use to switch to the UTILITY screen (P. 25).
15 Rotary selector dial
When in the BROWSE and UTILITY screens, rotating the dial
allows track selection and movement of the cursor between
selection items. Press the dial to confirm the selection.
For operations in the MIX and EFFECT screens, consult the
DJS Control Guide.
16 CUE/LOOP MEMORY button
Not used during DJS control.
17 CUE/LOOP CALL button
Not used during DJS control.
TRACK SEARCH
CUE/LOOP
EJECT
TIME
A.CUE
IN/CUE
HOT LOOP
LOOP
RELOOP/EXIT
PITCH BEND
BROWSE MIX EFFECT UTILITY
MT
0
MASTER
TEMPO
TEMPO
6/10/16WIDE
OUT/ADJUST
FWD TEMPOREV
MEMORY CALL
SEARCH
QUE
J
O
G
B
R
E
A
K
S
C
R
A
T
C
H
TRACK SEARCH
CUE/LOOP
EJECT
TIME
A.CUE
IN/CUE
HOT LOOP
LOOP
RELOOP/EXIT
PITCH BEND
MT
0
MASTER
TEMPO
TEMPO
6/10/16WIDE
OUT/ADJUST
FWD TEMPOREV
MEMORY CALL
SEARCH
QUE
J
O
G
B
R
E
A
K
S
C
R
A
T
C
H
A
LOAD
B
SEP-C1
LOAD
1
16
8 23 2 3 11 12 13 14
19
19 15 21
22
2024
18109
17
7
6
4
5
AUTO CUE function
Whenever a track is set or track search is performed, this
function automatically sets a cue point and cue standby
immediately before the point where music starts.
SEP-C1_EN.book 10 ページ ２００８年３月２４日 月曜日 午前１０時５２分