Filter
Top Products
ç
Ì
ÎÑËÞÔÛÍØÑÑÌ×ÒÙ
ÒÑÌÛæIf you are having problems after installation follow the Troubleshooting procedures below.
Ю±½»¼«®» ïæݸ»½µ ß³°´·º·»® º±® °®±°»® ½±²²»½¬·±²-ò
Ê»®·º§ ¬¸¿¬ ÐÑÉÛδ·¹¸¬ ·- ±²ò׺ ÐÑÉÛÎ ´·¹¸¬ ·- ±² -µ·° ¬± ͬ»° íô·º ²±¬ ½±²¬·²«»ò
1.Check in-line fuse on battery positive cable.Replace if necessary.
2.Check fuse(s) on amplifier.Replace if necessary.
3.Verify that Ground connection is connected to clean metal on the vehicle$s chassis.Repair/replace if
necessary.
4.Verify there is 9 to 16 Volts present at the positive battery and remote turn-on cable.Verify quality
connections for both cables at amplifier,stereo,and battery/fuseholder.Repair/replace if necessary.
Ю±½»¼«®» îæЮ±¬»½¬ ±® ̸»®³¿´ ´·¹¸¬ ·- ±²ò
1.If the Protect light is on,this is a sign of a possible short in the speaker connections.Check for
proper speaker connections and use an ohm meter to check for possible shorts in the speaker wiring.
Too low of a speaker impedance may also cause Protect to light.
2.If the Thermal light is on,check for proper speaker impedance,rewire if needed.This can also be a sign
of driving the amplifier at very high power levels without adequate airflow around the amplifier.Shut
off the system and allow amplifier to cool.Check that the vehicle charging system is maintaining
proper voltage.If the previous items do not solve the problem,a fault may be in the amplifier,call
customer service for support.
Ю±½»¼«®» íæݸ»½µ ß³°´·º·»® º±® ¿«¼·± ±«¬°«¬ò
1.Verify good RCA input connections at stereo and amplifier.Check entire length of cables for kinks,
splices,etc.Test RCA inputs for AC volts with stereo on.Repair/replace if necessary.
2.Disconnect RCA input from amplifier.Connect RCA input from test stereo directly to amplifier input.
Ю±½»¼«®» ìæݸ»½µ ß³°´·º·»® ·º §±« »¨°»®·»²½» Ì«®²ó±² б°ò
1.Disconnect input signal to amplifier and turn amplifier on and off.
2.If the noise is eliminated,connect the REMOTE lead of amplifier to source unit with a delay turn-on
module.
ÑÎ
1.Use a different 12 Volt source for REMOTE lead of amplifier (i.e.battery direct).
2.If the noise is eliminated,use a relay to isolate the amplifier from noisy turn-on output.
Ю±½»¼«®» ëæݸ»½µ ß³°´·º·»® ·º §±« »¨°»®·»²½» »¨½»-- Û²¹·²» Ò±·-»ò
1.Route all signal carrying wires (RCA,Speaker cables) away from power and ground wires.
ÑÎ
2.Bypass any and all electrical components between the stereo and the amplifier(s).Connect stereo
directly to input of amplifier.If noise goes away the unit being bypassed is the cause of the noise.
ÑÎ
3.Remove existing ground wires for all electrical components.Reground wires to different locations.
Verify that grounding location is clean,shiny metal free of paint,rust etc.
ÑÎ
4.Add secondary ground cable from negative battery terminal to the chassis metal or engine block of
vehicle.
ÑÎ
5.Have alternator and battery load tested by your mechanic.Verify good working order of vehicle
electrical system including distributor,spark plugs,spark plug wires,voltage regulator etc.